Follow these steps to reconnect your IHD:
- Unplug the IHD and let it run out of power completely.
- Leaving the IHD unplugged, restart it by pressing the round, flat button on the back.
- Let the emergency power reserve run out completely.
- Plug the IHD in to recharge it, then switch it back on.
How do I connect my smart meter to display?
It usually takes about three hours. Press and hold the power button on the back of your smart meter display to turn it on. To turn it off, press and hold the same button for five seconds. Each time you turn the smart meter display on, it will show ‘Welcome to IHD2’ then ‘Attempting to pair’.
What do I do when my electricity meter display is blank?
Why is my electricity meter blank? Meters can go into sleep mode and seem to have no display. Pressing a button on the main panel should revive the screen display. If you’re worried your meter is broken you need to get in contact with your energy provider and they’ll tell you what to do.
How do I reset my smart meter monitor?
To reset it it turn it right off by holding down the power button for 10 seconds and then power it back on again, it should work.
Why has my in-home display stopped working?
Try moving your In-Home Display closer to your electricity smart meter. Once you’re there, turn it off using the round, flat button at the back. Wait a minute and then press the button again to switch the IHD back on. Sometimes, this gives it the boost it needs to get going again.
Why is my smart meter monitor not working?
If your smart energy monitor stops working check your power cable is inserted correctly and that your power supply is switched on at the wall. If it’s still not working, try using batteries. If batteries fix the issue, then the problem is with the cable.
Why is my prepaid meter not showing light?
An incident where your prepaid meter is showing a blank screen happens when their is a disconnect between your meter token gadget and the sub power transmitter adapter connected to it. Loose wires is a major cause for this problem.
What is the red flashing light on my smart meter?
There is energy consumption in most meters. It means that energy consumption has gone up if it blinks very quickly. The power supply is shut down when the red light is on because the contracted power has been exceeded.
How do I restart my home screen?
Follow these steps to reconnect your IHD:
- Unplug the IHD and let it run out of power completely.
- Leaving the IHD unplugged, restart it by pressing the round, flat button on the back.
- Let the emergency power reserve run out completely.
- Plug the IHD in to recharge it, then switch it back on.
How do I reconnect my British Gas smart meter?
Restore my electricity supply using my meter
- Look at the meter reading screen on your electricity meter.
- Press A twice.
- Press B to restore the electricity supply.
How do I connect to IHD?
Signal bars solid > IHD is paired.
1. Using your IHD this is the easiest and fastest way:
- Tap the menu icon at the bottom right of the screen.
- Press Top-Up.
- Choose the fuel you want to top up.
- Press OK.
- Enter your PayPoint code.
- Tap OK.
- The IHD will then confirm that your money has been added to your meter.
Why has my EON smart meter stopped working?
It may be because your smart meter hasn’t been able to talk to us and send us your readings. A weak signal or a blocked meter* could be the cause of this.Please clear the space around your meter and If you have something that can’t be moved, please call us on 0345 055 0065 to see if we can help.
How do I reset my British Gas Electric monitor?
Using a paper clip or small screwdriver, press the reset button which can be found about halfway down the side of the sensor. You will need to press the reset button 4-6 times until the LED inside the sensor starts to double flash. Reconnect the sensor back on your electricity meter.
How do I reset my prepaid meter?
To reset your prepaid meter, make sure all your appliances are switched off, this is very important. Then Press the ‘I’ key then 008 on the device, a screen will appear showing your consumption days and other information, press the ‘I’ key again twice to reset your prepaid meter.
How do I activate my prepaid meter?
How to activate conlog prepaid meter
- If your prepaid meter number begins with 45 or 46, type in your meter number and press enter.
- Type the 1st 20 digits of your meter activation token, then enter.
- Type the 2nd digits of your meter activation token, then enter.
Why is my CIU showing failed?
Possible Cause. The Customer user Interface Unit is not having a strong communication link with your meter through the power source. Weak batteries inserted into the Customer user Interface Unit. The Customer user Interface Unit not paired with the meter.
How do I get my electricity back after disconnecting?
Reset the main breaker by turning the switch off and on two times. Leave the switch in the on position. Return to the breaker panel inside your home and turn each breaker back to the on position, one by one. In many cases, power is now restored.
How do I turn on my electricity after its been disconnected?
If you have been disconnected and can’t work out an arrangement with your supplier to get reconnected, call us on 1800 246 545. Our services are free, fair and independent. There are rules about when and how a provider can disconnect your electricity or gas supply.
What lights should be on my smart meter?
My understanding of the ‘red and green‘ lights on the smart meter information box is that the green light indicates that energy is being use efficiently, i.e., low power use, and the red light indicates high power use.
What does it mean when your electric meter is blinking?
If the LCD screen is flashing various numbers, letters, and symbols, then the meter has electricity supplied TO THE METER. So, if you see the letters OPN the electricity is OFF. There is NO power being supplied PAST the meter.The electricity has been disconnected due to non-payment of a past due bill.
Why does my electric meter have a red light?
The red light stays on if you consume 1 watt-hr. When the power is below a preset level, it’s continuous. In the case of power export from, it would mean fraudulent use.
Contents