How Do I Put A Lock On My Iq Panel?

How do I lock my IQ panel?

From the home screen of the IQ Panel 2, verify that the lock is listed on the right side of the screen. Then swipe the screen to the right until you access the locks menu. Pressing the large green key will lock the door. Press this button, and make sure that the door can be locked and unlocked.

How do you bypass the IQ Sensor?

To bypass a sensor:

1. Press System Disarmed.
2. Press the > arrow (to the right of the Arm Away icon) to expand the display.
3. On the top right of the screen, press ALL. This will list your sensors.
4. Select the sensors you’d like to bypass and press either Armed Stay or Armed Away.

What is the installer code for IQ panel?

1111
The Installer Code (default 1111) on a Qolsys IQ Panel 2 Plus has the second-highest authority level on the system, after the Dealer Code (default 2222). You can use the Installer Code to change most system programming settings.

How do you install a Yale lock?

Open the Yale Secure app and create a new home by tapping the + icon in the top right corner. Tap the + icon next to your home name to add a new lock. Tap the Yale lock when it appears as an available device.

How do you trigger a Yale lock?

Enter the new Master PIN code (4~8 digits), followed by the key. Touch lock with back of hand or fingers to activate. Press the key to activate. Touch lock with fingers spread to activate.

How do you put a Z-wave door lock on?

IQ Panel 2 – Add Z-Wave Door Lock

1. Press or swipe down clock display at top for Settings Tray then press SETTINGS.
2. Press ADVANCED SETTINGS then enter Installer Code 1111.
3. Press INSTALLATION then DEVICES.
4. Press Z-WAVE DEVICES then ADD DEVICE.
5. Press PAIR, IQ Panel 2 enters Z-Wave learn mode.
6. Kwikset Deadbolt.
7. Schlage Deadbolt.

How do I add smart plug to alarm com?

You can add a Z-Wave device to your Alarm.com SEM by clearing the device from the network, putting the SEM in its enrollment mode and activating the inclusion function on the Z-Wave device. The lights on the SEM module should then indicate that a Z-Wave device has been learned-in.

How do you bypass a zone on a Brinks alarm?

Bypass a Zone

1. Enter the following: Your 4-digit code. The number 6 (bypass button) Two-digit zone number of the zone you want to bypass. (01, 02, 03, etc.)
2. Repeat this process for all zones you would like to bypass.
3. Once your system is disarmed, this process will need to be repeated in order to arm your system again.

How do you bypass a Brinks alarm sensor?

Simon XT

1. Press BYPASS;
2. Enter the MASTER CODE;
3. Scroll up/down until you reach the sensor you wish to bypass;
4. The display will show sensor name (ie Sn # Front Door) on the first line;
5. Press ENTER to bypass (deactivate) the sensor;
6. When a sensor is bypassed, the panel will display BYPASSED on the second line.

What is the master code for?

Master Code: The master code can do everything the installer code can, except enter system programming, enter certain test modes, and program any installer-only schedules.The master code can always arm or disarm the system, regardless which code was used to arm, or if the system was quick armed.

What is the default installer code?

5555
The default installer code for a DSC is 5555. The installer code is the code that is used to get into the DSC programming mode so you can set the system up and make changes to panel programming. Having the installer code is the most important part of setting up the system.

How do I turn on my IQ panel?

IQ Panel 2 – Power Cycle to Panel

1. Press or swipe down clock display at top for Settings Menu then press SETTINGS.
2. Press ADVANCED SETTINGS then enter Master Code.
3. Press POWER DOWN, then press OK to confirm and power down.
4. Wait 2 minutes, then press right side power button for 3 to 4 seconds to power up.

How do I turn off IQ 2?

You can disable a Qolsys IQ Panel 2 by powering the system down. The system has an option in the Advanced Settings Menu for performing this task. The system will be unable to do anything once it is powered down.

How do I pair my Kwikset 916?

1. Make sure the door is open. Press the Program button once.
2. Press checkmark symbol once.
3. Enter user code. A total of 16 user codes may be programmed. Each user code must be a unique code between 4 and 8 digits.
4. Press lock symbol once.

Is there an app for Yale lock?

In order to provide optimal service to all our users, Yale maintains app support for the two most recent operating systems for both iOS and Android platforms. More information about compatible devices is available in this article.

Do all Yale locks have Z-Wave?

The Yale Z-Wave Smart Module (AYR202-ZWV-USA) is compatible with all Yale Assure Locks and Levers. To control your lock with your phone, you must purchase a compatible Z-Wave Smart home hub.

What happens if Yale lock runs out of battery?

If you need, you can use a 9 Volt battery to temporarily charge the lock, so you can enter your passcode on the lock’s keypad to lock or unlock it.

Where is QR code for Yale lock?

When setting up your product, the app will ask you to first scan your Yale Access QR Code. This code is located on either documentation insider your packaging, on your smart module, or on the battery cover of your product. If you cannot locate your QR code, you can manually enter the serial number into the app.

Does ring work with IQ panel?

Yes, the IQ Panel 2 is very versatile. It has Bluetooth and Wi-Fi capability so you can add your Ring doorbell, smart thermostat, and other smart home devices to your home security network.

Does IQ panel work with Alexa?

Yes, you can connect an IQ Panel 2 Plus to Alexa. To do this, the system will need to be active with Alarm.com. You can use the Alexa App to enable the Alarm.com Skill and link your Alarm.com account with Alexa. You will then be able to control the system using spoken Alexa voice commands.