How to Disable a GM PassLock System
- Leave the ignition key turned to the “On” position after the vehicle has stalled and will not start.
- Look at the dashboard and locate the theft system light.
- Turn the ignition to the “Off” position to disable the PassLock system, and wait for 20 seconds for the system to reset.
How do I permanently disable PassLock?
Turn the key to the “off” position — and leave it there for 20 seconds — after the anti-theft light stops blinking. This disables the Passlock system; it is ready to “relearn” your key. Remove the key. Put the key back in the ignition, and start the vehicle.
How do I disable GM Anti-theft system?
Insert the car key into your car’s ignition and turn it on. The car’s accessories will be activated but not the engine. Step 3: Do another check on the anti-theft light. If it isn’t blinking any longer, then turn the key over to the Off position and let it sit for a couple of minutes.
Can you bypass the PassLock system?
The first, is to permanently bypass this system.The second way, is to temporarily bypass the PASSLOCK, by introducing relays into the system, which retain all of the features of the system, while allowing your remotes start module to bypass it automatically during a remote start cycle.
Where is PassLock sensor located?
There is only one PassLock system. There is no sensor in the ignition lock cylinder, the Passlock sensor is in the ignition lock cylinder housing, and there is a magnet in the ignition lock cylinder.
How do you disable a factory car alarm?
A large number of factory alarms turn off once you put the key in the lock of driver’s or even passenger doors. You can also try a similar method pressing the lock or unlock button on the remote fob. Unlocking the doors with the right remote fob will shut down most fabric alarms.
How do I disable anti-theft system GMC?
How to Disable a GM Passkey System
- Insert your GM key into the ignition, attempt to start the car, and let it stall. After it stalls, leave the key in the starter in the “On” position.
- Look at the “Theft Sys” light blinking on your dashboard and wait until the light stays on without blinking.
Is there a fuse for the anti-theft system?
It is usually located on the dashboard by the driver’s door, in front of your left knee. You may find the alarm fuse in this fuse box. If you do not find an alarm fuse inside of the car, look in the fuse box under the hood on the driver’s side. Your car model may or may not have additional fuse boxes.
How do I get my Chevy out of theft mode?
To reset the anti-theft system on the Chevy Silverado You will need to get into the car and lock the doors. Now with the doors locked put the key into the ignition and turn it to the on position. Let it sit there for 5 minutes until the anti-theft light blinks.
How GM PassLock works?
If it’s correct, the vehicle will start and run. If not, the vehicle may start but will stall within seconds. The VAT, or vehicle anti-theft was used primarily on 1986-88 Corvettes. The key had a pellet that was married to the vehicle anti-theft module at the factory.
How do I fix my PassLock GM?
How to Fix Passlock for Chevy Vehicles. A temporary fix is to leave your key in the ignition, at the auxiliary position for about 10-15 minutes until the security light shuts off. When the light shuts off you can try to start the engine again. Rinse, repeat, and cry.
How do I turn off anti-theft without key fob?
Ways to stop a car alarm without a keyfob
- Check your owner’s manual. Every vehicle is different.
- Lock your doors.
- Turn the car on.
- Turn the ignition to on and wait.
- Pull the fuse for the alarm.
- Pull the wires for your alarm.
- Disconnect the battery.
What years did GM use PassLock?
For the 1995-1/2 model year, General Motors introduced PASSLock, the first ignition lock equipped with a magnet mounted into the ignition lock cylinder and a corresponding Hall-effect sensor mounted into the housing assembly.
How do you relearn a Chevy key?
Relearn procedure:
Insert ignition key and turn to the ON position. Do not attempt to start the engine. Leave the key in the ON position for approximately 11 minutes. The security light will be on or flashing for the 11-minute period.
How do you turn off the pass code on a 2005 Chevy Colorado?
Truck is still not starting. To reset the 2005 Chevy colorado passlock put your key in the ignition in the on position, then back to the off position, then to the on position and then wait until the theft sys light stops flashing and then immediately turn the car on.
How do you bypass the security on a 1998 Chevy truck?
How to Reset Passlocks on ’98 Chevy Trucks
- Insert your registered key into the ignition. Try to start your Chevy truck. If the security feature was activated, you should not be able to start the truck.
- Turn the key back to the “Run” position. The security light will start to flash off and on.
How do you disable a car alarm with a key fob?
Quick fixes. In most vehicles, you can silence the alarm system by pressing the lock and unlock button on the key fob. Another common remedy is to manually unlock the driver’s side door with the key. If these two options don’t work, insert the key into the ignition and try starting the vehicle.
How do you turn off anti theft on a Chevy Silverado?
How Do I Reset Anti-Theft System: Chevy Silverado?
- Insert ignition key.
- Turn it to the on position.
- Attempt to start the engine.
- Leave the key in that position until the security light stops flashing.
- Once the light goes off, switch the ignition key to off.
- Wait about five seconds.
- Try to start the engine again.
Will disconnecting battery reset anti theft?
It is another way to solve the problem of anti theft system car wont start. Disconnect the positive terminal of the battery for a minute or two.It will reset the computer system and your car is likely to kick off. In case the trick fails, reset the factory alarm by activating its built-in kill switch.
Will removing fuse disable car alarm?
You’ll need to locate the fuse responsible for your car alarm’s power. Fuses send electricity to different parts of your car, so removing the alarm’s fuse won’t stop power from the overall battery connected to your engine (remember, car alarms need to run when the engine is off, so they have a distinct fuse).
How do I disarm my Immobiliser?
Turn the key to unlock your car door, but don’t release it. Hold the key in this position for 20 to 30 seconds. This lets the system know you have the correct key, and it can allow you to bypass the alarm system. Some vehicles recognize the key simply by turning the key back and forth in the door lock key cylinder.
Contents