Hold the thermostat approx 2 metres away from boiler. Locate the gateway adjacent to the house wireless router and connect the supplied ethernet cable from the gateway to the wireless router as shown. Connect the Gateway power cable and 3 pin plug together, then connect the 3 pin plug to a convenient mains socket.
Why is my ideal thermostat not pairing?
Check the batteries are inserted correctly. Replace the batteries in the thermostat. Make sure the target temperature is at least 1°C higher than the actual room temperature on the thermostat.Check the Touch thermostat is within range of the boiler transceiver.
How do I connect a wireless thermostat to my boiler?
To connect a smart thermostat to your boiler, the thermostat will require a power source (battery or wired), as well as a receiver box if one is required. Use the screen and the buttons on the thermostat to navigate the system. In some cases, both devices will automatically connect when they are turned on.
How do I reset the thermostat on my ideal boiler?
REsET PROCEDURE
To reset boiler, turn the mode control knob (D) to reset position and immediately turn knob back to required setting. The boiler will repeat the ignition sequence. If the boiler still fails to light consult a Gas Safe Registered Engineer or in IE a Registered Gas Installer (RGII).
What is ideal touch connect?
The Ideal Touch Connect Alexa app allows you to control your heating by adjusting the target temperature and changing the heat mode.
Why is my thermostat not connecting to boiler?
When you have a wired thermostat that does not properly control the boiler, the problem can either be due to a faulty wiring, a damaged component, or an outdated unit. In all 3 cases, you need to be able to access the inner components, so get ready to open your thermostat.
How do I fix an unresponsive thermostat?
If the thermostat is still unresponsive, make sure the breaker is shut off and remove the cover. If it looks dirty inside, use canned air or a soft artist brush to clean away accumulated grime that may be affecting its functionality. Then look for issues like loose wiring or terminal screws and tighten them up.
How does a thermostat work with a combi boiler?
It uses a sensor to monitor the temperature of your home, and consequently it keeps an eye on what your boiler is up to. If your room thermostat senses that your home has reached its target temperature, it will switch the central heating off. Once the temperature drops, it’ll fire up the boiler again.
Why does my thermostat say no signal?
If the heating is on you will see an ON message on the thermostat display. When you can see that the ‘status’ and ‘central heating’ lights on the receiver have turned green you’re done! If your thermostat is still showing a ‘No Signal’ message, your heating devices should be manually reset and paired.
Why is my boiler flashing L2?
The Ideal boiler L2 fault means there is flame loss or some issue that can lead to a lockout. This can happen during operation due to low gas pressure, faulty gas valve, or flue sensor.
Why is my ideal thermostat flashing?
If a battery symbol is blinking, the display is blinking or the display is blank then replace batteries. 1. During normal operation light (A) is on for Hot water Operation.If less than 4 lights are on either the room thermostat is too far from the boiler or the batteries in the room thermostat need replacing.
Can I control my ideal boiler from my phone?
You’re in control. The Ideal Touch Connect heating app allows complete control of your heating system anytime and anywhere from your smart phone and web browser.With over 40 time and temperature periods per week, the Touch app can handle even the busiest of lifestyles with ease.
Why is my boiler not firing up?
A boiler might not ignite due to various possible reasons insufficient pressure, blockage in the burner, faulty valves, frozen pipes etc. Sometimes, you can fix the problem on your own. In other cases, you don’t have any choice but to call an engineer.
How do I reset my pro1 thermostat?
The thermostat can be reset by power cycling. Power cycle the thermostat by removing if from the subbase and remove the batteries (some thermostats will not have batteries). Wait 10 seconds and then replace the batteries and place the thermostat back on the subbase.
How do I reset my thermostat after changing the battery?
Factory Reset the Thermostat
- Ensure that your thermostat is turned off.
- Open the door of the battery compartment.
- Now take out the batteries.
- Put the batteries back on in reverse to the indicated polarity by the markings in the battery holder.
- Allow the batteries to stay this way for about five seconds.
Why does my thermostat setting not match my home’s temperature?
If your thermostat is not able to accurately read the temperature in your home, it will not be able to regulate it properly either. It is possible that your thermostat is dirty inside, which can affect its reading of the temperature.
What should a boiler thermostat be set at?
If you have a conventional boiler system, your water cylinder will have its own thermostat. This is usually fitted on the side of the tank. You should set the temperature between 60 and 65 °C but for maximum efficiency, it should be set to around 60 °C.
What temperature should my combi boiler be set at for central heating?
Adjust the boiler controls
Combi boilers have controls on the unit which allow you to set the temperature of the water that will be circulating around the central heating system and out of the taps. The best setting for combi boilers is often recommended as 75°C for central heating and 60°C for domestic hot water.
How do I put my hive thermostat in pairing mode?
If you already have a Hive Hub just put it into pairing mode. To do this press the button at the rear of the hub for 1 second and release it. The middle light should now flash AMBER showing it is in pairing mode.
How do I resync my hive thermostat?
Press and hold down the ‘back arrow’ button and the ‘menu’ button on the thermostat at the same time (these are the bottom left and bottom middle buttons below the silver dial). Keep these buttons held down together until the thermostat display says ‘Welcome, searching’ then remove a battery from the thermostat.
How do you turn on the heating on an ideal boiler?
To switch preheat on or off, move the domestic hot water preheat knob (B) full clockwise and then return it to the required domestic hot water temperature setting. The boiler will operate periodically for a few seconds to maintain the domestic hot water heat exchanger in a preheated condition.
Contents