How Do I Optimize Ecobee?

Top 10 ways to get the most out of your ecobee thermostat

1. Handsfree temperature control with virtual assistants.
2. An easier way to build a schedule.
3. Troubleshoot for accurate temperature readings.
4. Balance the temperature throughout your home.
5. Override the scheduled temperature for better comfort.
6. Protect your home.

Should my ecobee be on auto or heat?

Auto mode on your ecobee thermostat is great for maintaining a comfortable home temperature in milder climates or in-between heating and cooling seasons.

How does ecobee optimize for humidity?

ecobee detects fluctuations in indoor humidity to ensure your home always feels like the temperature you’ve set on your thermostat. This keeps your home energy efficient and comfortable even in periods of unusually high or low humidity.

Does ecobee need to be calibrated?

The Ecobee thermostat requires calibration to get an exact reading of the room temperature which takes around 20 minutes. Note-Remember not to use AC or heater during your ecobee calibrates.

How do I calibrate my Ecobee thermostat?

To Configure Temperature Correction

1. Press Menu on the main screen.
2. Go to Settings.
3. Then go to Installation Settings.
4. Select Thresholds.
5. Then select Temperature Correction.
6. Adjust the temperature reading to fit your needs.

What is Stage 1 cooling?

A single stage heating or cooling system means your furnace or air conditioner has only one level of heat or cold output. Single stage thermostats are used to control single stage HVAC systems—thus, if you have a single stage heating and cooling system, your home needs a single stage thermostat.

How do I use Ecobee auto mode?

To be able to set your ecobee Smart Thermostat to Auto mode, you need to enable the feature first.
To Enable Auto Mode

1. Press Menu on the main screen.
2. Go to Settings.
3. Then go to Installation Settings.
4. Select Thresholds.
5. Select Auto Heat/Cool.
6. And choose Enable.

How do I change my Ecobee comfort settings?

How to Access & Adjust Comfort Settings

1. Wake up your ecobee Smart Thermostat, then tap Menu.
2. Tap Comfort Settings.
3. Select the Comfort Setting you wish to customize.
4. Tap the temperature controls to open them.
5. Adjust to the desired temperature, then tap Save.

How is your O B reversing valve energized?

Heat pumps will have a reversing valve, which switches the heat pump from heating mode to cooling mode. The valve will operate in one of two ways: 1) O reversing valve (energized in cooling) or 2) a B reversing valve (energized in heating).

Does ecobee measure indoor humidity?

Does ecobee Control Humidity? Yes! The ecobee smart thermostat can control the humidity in your home. Most of its power to control your humidity comes down to your HVAC system.

Does ecobee show indoor humidity?

The Ecobee has a humidity sensor that can sense the changes in the humidity indoors. It adjusts the “feels like” temperature to ensure that your home feels how you want it to, even when the humidity may fluctuate. However, you may not be able to control the humidity with the Ecobee.

What is Ecobee calibrating?

The “Calibrating” message on your Ecobee thermostat screen indicates that it is measuring the current indoor temperature. Ecobee calibrates once it’s installed initially or when it reboots, and it typically takes around 5 to 20 minutes.

How do I bypass Ecobee calibration?

If your Ecobee is calibrating for an unusual amount of time, try power cycling it by removing the thermostat from the wall and then putting it back. Then, wait 20 minutes to see if it stops calibrating.

Is Ecobee sensor accurate?

The ecobee temperature sensor has a +/- 1.0F accuracy and is programmed to provide readings every 15 seconds.

How do I reset my ecobee thermostat?

How to Factory Reset an ecobee Smart Thermostat

1. From the Home screen, press Menu.
2. Select Settings.
3. Go to Reset.
4. Choose Reset All Settings then confirm your selection by pressing Yes.
5. Choose the reset option that suits your needs:
6. The ecobee thermostat will be reset to factory defaults.

How do I troubleshoot my ecobee thermostat?

Open the panel on your furnace to expose the control panel where your thermostat wires are connected. Most systems have a purple 3 or an orange 5 amp fuse on the board—check this fuse to ensure that it’s intact. A blown fuse will have to be replaced. Once a blown fuse is replaced, the ecobee should power back on.

Does ecobee automatically update?

ecobee devices will update themselves automatically, provided they are connected to Wi-Fi. When a firmware version is ready for the public, it will be pushed out gradually over a period of time to all applicable ecobee devices.

What is 2 stage air conditioner?

Two-stage cooling refers to the type of compressor that’s in the outside condensing unit. This feature allows for two levels of operation depending on your cooling needs — full capacity on hot summer days or part capacity for milder days.

Do I need a 2 stage thermostat?

To sum it up: If you plan to keep your home at a constant temperature, you don’t need a two-stage thermostat. If you want to vary the temperature of your home during the day or night, a programmable two-stage thermostat is the way to go.

Is a 2 stage air conditioner worth it?

For those who are looking for something more efficient, two-stage and variable speed systems are worth considering. These units have fewer instances of cycling on and off, which allow you to enjoy: Lower energy bills. More effective humidity control.

What is Auto mode in ecobee?

In Auto mode, the thermostat will engage both your heating or cooling as necessary. This mode is most useful if you live in a region where the temperature fluctuates regularly or you’re in the middle of a season change and you may need both heating and cooling at different times during the day.