How Do I Manually Start My Hunter Sprinkler System?

Why isn’t my hunter sprinkler system working?

If your controller shows irrigation running (Flashing Sprinkler Icon), and your sprinklers are not working, you may have a wiring problem at the valves or the irrigation water supply has been shut down.Check the wiring connections at the master valves for loose or corroded connections, or a bad solenoid.

How do I turn my hunter node back on?

To turn the controller back on, use the center button to return to the home screen and allow the controller to go to sleep in that position. To turn your controller off, press the button until the icon and Off is displayed on screen. After a short period of time the display will shut off to retain battery power.

Why won’t my sprinkler system turn on manually?

Here are some common reasons why your sprinkler system won’t turn on: Lawn sprinkler control timer isn’t working correctly. Clogged or dirty sprinkler heads. Broken sprinkler heads.

Why wont my sprinklers turn on manually?

If Sprinkler Zones Do Not Turn On
When the sprinkler zones do not turn on at all, it is generally a problem with the electrical signals running from the controller to the valve solenoids. More rarely, it is caused by a faulty valve that needs to be rebuilt or replaced.

How do I reset my Hunter SRC Plus sprinkler?

SRC Plus Reset

1. Press and hold down the , and buttons.
2. Press and release the RESET button in the lower wiring compartment.
3. Release the , and buttons. The display should now show 12:00a. m.
4. All the memory has been cleared and the controller may now be reprogrammed.

What does no AC mean on Hunter sprinkler?

Pro-C – “NO AC” on Display The “NO AC” display is a diagnostic message telling you that the controller has stopped receiving AC power. The controller is running on the power supplied by the backup battery. Check the power source by plugging a lamp or radio into the wall outlet to verify there is power at the outlet.

What is RS on Hunter SRC Plus?

The function of RS terminal was to notify the controller the status of the rain sensor.

Where is reset button on orbit?

Push the “Reset” button (located in the bottom-right corner) to clear all previously programmed data if you’re programming the Orbit sprinkler timer for the first time.

How do I turn on my orbit sprinkler system after winter?

Steps to turn on sprinkler system after wintering

1. Find system’s main shut-off valve.
2. Find the vacuum breaker.
3. Close the vacuum breaker test valves.
4. Open the vacuum breaker’s shut-off valves.
5. Reinstall main valve bleeder cap (as needed).
6. Slowly open the main valve.
7. Test the system.
8. Recheck the vacuum breaker and valves.

Why is my orbit Sprinkler not working?

If you are still not getting power, the timer may be defective. Turn the flow-control stem located at the connection from the Orbit to the main water line in a counterclockwise direction if one or more of the sprinklers is not responding to programming.Recheck the programming of the Orbit to ensure it is correct.

How does the hunter node work?

The Node mounts to a valve solenoid quickly and easily, and without screws, drills or additional wires.Once placed in a valve box, the Node is operated by one or two 9V batteries, which provide standard or extended power throughout the season.

How do you set the time on a Hunter node?

To set the time and date on the node press the center button, simply scroll through the choices using the left and right arrow buttons and adjust the displayed item using the plus and minus buttons. Push the button until the icon is displayed. All 4 digits will be displayed representing the year.

Where is the reset button on a Hunter thermostat?

Press and release the RESET button on the back of the front panel.

How do I reset my hunter X2 sprinkler?

X2 – Total Reset

1. Turn the dial to the RUN position.
2. Press and hold the program button.
3. Press and release the RESET button located inside the lower wiring compartment.
4. When the display reads the controller station count; (e.g. 14) then DONE, release the PRG button.

How do you set a Hunter sprinkler timer?

How to Program Your Hunter X-Core Sprinkler System

1. Step 1: Set The Current Time. First, you will want to ensure that the current time is correct.
2. Step 2: Set the Start Times. Next, turn the dial to “Start Times”.
3. Step 3: Set the Run Time.
4. Step 4: Set the Watering Days.
5. Step 5: Test Coverage.
6. Step 6: Finished!