SimpliSafe does not have a range extender or the ability to link two base stations. The DIY set-up method to ensuring maximum range on your security system is to move your sensors and base station around testing them intermittently until you find a configuration that works.
How do I extend my SimpliSafe sensor range?
You can boost signal by extending its antenna, which is very inexpensive and relatively easy to do. This MAY be enough to get your base station and sensor talking too each other again. Happily, it is straightforward to boost sensor signal output significantly by extending its antenna.
How far away can SimpliSafe sensors be?
The base station can reach sensors up to 400 feet away. However, all keypads need to be within 100 feet of the station to work properly.
How do I adjust the sensitivity on my SimpliSafe motion sensor?
You can locate the sensitivity switch in the battery compartment of the motion sensor. To increase the sensitivity, raise the switch up. To lower it, push it down! High sensitivity increases the range of the motion sensor to 35 feet and above.
How many sensors can be connected to SimpliSafe?
All components are equipped with adhesive strips for installation, as well as screws in case you want them to be more secure. You can have up to 41 sensors synchronized to your Original SimpliSafe system, and in ideal conditions they can send signals up to 400 feet away from the Base Station.
How do I fix the SimpliSafe keypad range?
Either unplug the base station and bring it closer to the keypad, or slide the keypad off its bracket and bring it closer to the base station. Try to arm the system through your keypad, and see if it works. If it does, try moving your base station to a slightly closer location to your keypad.
What frequency does SimpliSafe use?
433.92MHz
The host explains that SimpliSafe’s sensors communicate with the base on the 433.92MHz frequency, which is very popular among other consumer electronics, like garage door openers, baby monitors, and more.
How do you jam a motion sensor?
How to Fool Motion Detectors
- Learn how the motion detector works.
- Trip the motion detector on purpose until the homeowner switches it off.
- Reduce the amount of heat you’re giving off.
- Introduce a masking sound.
- Figure out the paths of the detectors.
- Move very slowly.
Can SimpliSafe be hacked 2021?
SimpliSafe is not easily hacked
While it’s technically possible to hack into anything, calling it easy is extremely misleading.
Why does my SimpliSafe motion sensor keep going off?
Direct sunlight hitting the sensor can trigger a false alarm. Heating vents located in the room. If they are located within the sensor’s field of vision, they may cause false alarms. Pets that are able to get too close to the sensor.
By adding a panic button to your system, your security alarm can protect you and your family when you’re home, whether or not your system is armed!Alternatively with a SimpliSafe panic button, if you don’t want to alert an intruder to the authorities, you can set your panic button to ‘silent alarm’ or ‘duress’.
How far does SimpliSafe glass breakage work?
20-foot
Act fast against burglaries with this SimpliSafe glass break sensor. It triggers an alarm if it detects the sound of shattering glass within its 20-foot range, providing reliable security even when no motion detector is used.
How far away does SimpliSafe camera detect motion?
90 degrees
Your camera’s motion detection range is 90 degrees left to right and downward, as well as straight out. This range cannot be changed. There is also a notification “quiet period” set up by default. This means you should only be receiving a push notification every five minutes, per location.
Do New SimpliSafe sensors work with old system?
If you purchased a system in 2017 or earlier, you have the Original SimpliSafe.New sensors can be added to our latest SimpliSafe system in one of two ways. If you are adding a single sensor, open the Menu on your keypad (using your Master PIN) and select Devices, then Add device and follow the instructions.
Do I need a security sensor on every window?
Motion detectors will need to be placed in specific zones of your home, while window sensors should be placed at every window. When you build a comprehensive security system, you often use different types of sensor and detector in different areas.
Does SimpliSafe work on multiple floors?
Our sensors stay connected across multiple rooms and floors. While garages and basements, which have thick walls, can occasionally present a challenge, we’re confident our system can work for your home. If you have any concerns about your location, please contact customer support for a consultation (1-800-297-1605).
Why does my SimpliSafe keypad says out of range?
Keypad Out of Range is a generic message that appears on your Keypad whenever the device is not communicating with your Base Station.The Keypad is too far away from the Base Station. There is some other device between your Keypad and Base Station that is inhibiting their ability to communicate with each other.
The Keypad is used to arm and disarm your system. Also, in case of an emergency Keypads have a red panic button, which will trigger the alarm if you press and hold it for more than two seconds. Customers can change their system and device settings through their Keypad’s menu as well.
Can you have 2 SimpliSafe base stations?
SimpliSafe does not have a range extender or the ability to link two base stations. The DIY set-up method to ensuring maximum range on your security system is to move your sensors and base station around testing them intermittently until you find a configuration that works.
How do burglars get past alarm systems?
Most alarm systems send a signal through phone lines when someone breaks in.Another way criminals may try to defeat burglar alarms is through wireless alarm jammers. These very expensive devices are sometimes able to block cellular signals, such as the ones used in wireless home security systems.
Does SimpliSafe deter burglars?
SimpliSafe uses cellular to signal the monitoring service for help, so there are no phone lines for burglars to cut. Police will arrive no matter what. Plus it has a loud 85dB siren in the base station, with the option for a second 105dB siren, which will drive off most burglars.
Contents