In the Wyze app, tap on your Wyze Video Doorbell. Tap on the Settings gear on the top right. Tap Accessories > Your Chime > Tunes. Select your preferred Tune.
How do I get my WYZE chime to work?
To set up your Wyze Chime:
Plug your chime into a standard power outlet close to the doorbell. Press and hold the reset button on the bottom of the Wyze Chime until the blue light flashes quickly three times. Set up should complete automatically. Tap Finish.
What does WYZE chime do?
Wyze Chime can sound alerts up to 90+ dB. One chime provides enough audio coverage for up to one floor of an average house (approximately 1,000 sq ft). An extra chime is recommended for any additional floors, garage, backyard, or rooms with extra soundproofing.
What sounds does the WYZE doorbell make?
One chime is included with each Wyze Video Doorbell. Choose from 19 different chime sounds including traditional bells to birds chirping.
How do I reset my WYZE doorbell?
To factory reset your doorbell and chime:
- Press and hold the button on the side of Wyze Chime Pro for 3-5 seconds until it says “Reset successfully”.
- The WiFi signal LED will start flashing red > solid yellow > flashing yellow.
- The device is now ready to be set up again.
How do you connect a chime to a WYZE doorbell?
Plug your chime into a standard power outlet close to the doorbell. Press and hold the reset button on the bottom of the Wyze Chime until the blue light flashes quickly three times. Set up should complete automatically. Tap Finish.
How do you power cycle the WYZE doorbell?
To power cycle, your Wyze Wired Doorbell, flip the breaker, power the doorbell to its Off position, wait 10 full seconds, then flip the breaker switch back to the On position. Unplug your router for 10 full seconds, then plug it back in.
Can WYZE connect to ring?
Wyze cameras don’t integrate with Ring directly, but both Ring and Wyze devices work with Amazon Alexa. If you have a Wyze indoor camera and a Ring Video Doorbell, then you can control both from your Alexa devices.
Can I change WYZE doorbell chime?
To change the Wyze Chime tone:
In the Wyze app, tap on your Wyze Video Doorbell. Tap on the Settings gear on the top right. Tap Accessories > Your Chime > Tunes. Select your preferred Tune.
Can you use existing chime with WYZE doorbell?
No, your existing chime won’t work.
Hardwired and non-Wyze chimes will be bypassed so that the power can be used for your Wyze Video Doorbell.
Does WYZE doorbell have SD card?
No. Wyze Video Doorbell does not support a microSD card. All recorded events will be stored in the cloud.
How do I reconnect my WYZE doorbell to a new WiFi?
Steps to Connect Wyze Cameras to New Wi-Fi
Log in if you haven’t set the app to remember you. Connect your Wyze camera to the USB port or a power outlet. Wait until it flashes yellow (about thirty seconds). Hold the Setup button on the back of the camera until you hear the automated message ready to connect.
Why does my WYZE doorbell camera keep going offline?
Power Cycle your network
Unplug your router for 10 full seconds, then plug it back in. This will reboot the network and clear up any potential channel congestion that may be causing trouble for the doorbell.
Why is my WYZE camera offline?
Make sure the Wyze Cam Outdoor is charged. A low battery can cause poor connectivity. Check the battery level from the Home screen of the Wyze app, under the camera’s name. If the battery is low, charge the camera for 4 hours to guarantee a full charge.
Does WYZE doorbell require transformer?
To install a Wyze doorbell without an existing doorbell, you need a plug-in transformer to power the Wyze doorbell and a plug-in chime to announce visitors. Simply connect the wires of the plug-in transformer to the Wyze doorbell and plug it into a power outlet.
How do you take a WYZE doorbell off the wall plate?
To remove our Wyze Video Doorbell:
- At your doorbell, press hard inwards and up. This will unlock the doorbell from the wall plate or wedge.
- Work backwards using the Installation Guide. Remove the wire caps, disconnect the wires, and remove the wall plate or wedge.
What is a doorbell transformer?
The transformer is a metal box with two terminals connected to the doorbell wires. It takes the standard electrical voltage in your home, in most cases 110 to 120 volts, and lowers it to about 10 to 24 volts. This keeps doorbells powered at the right voltage for optimal operation.
How do I contact WYZE?
Customer Support
There are many ways to contact us, our phone number is (206) 339-9646, or you can chat with an agent or create a ticket on the support site. We’re open for support between 4 am – 8 pm PT Monday through Friday, and 8 am – 6 pm PT Saturday and Sunday.
How do I reset my WYZE outdoor camera?
Unplug the base station from power, wait 5-10 seconds, then plug it back in. Once the status light is solid blue, the reboot is complete.
What’s compatible with ring?
Ring-compatible devices
- Video doorbells and cameras.
- Smart locks.
- Smart lights and bulbs.
- Plugs and wall outlets.
- IFTTT and Z-Wave devices.
- Smart speakers and TVs.
- Garage doors, water valves, thermostats.
How does Alexa connect to ring device?
How to use Alexa to control your Ring security device
- Open your Alexa app on your iPhone or Android device.
- Tap the horizontal bars in the top left of the app screen.
- Select the Skills & Games option in the menu that appears.
- Enter Ring into the search bar.
- When Ring appears as a result, tap the Enable button.
Contents