– To confirm this is causing problems, remove one filter and run the pump, putting your hand over the return inlet to feel the jet of water. If the water stops flowing as soon as you reconnect the filter (and you then get E02), it means the filter is the only thing obstructing water flow. To fix: – Replace the filters!
Why does my Coleman Hot Tub say E02?
The E02 error code can occur when the filters are dirty or blocked. KINKED OR BENT LINER PIPES.
How do I fix error code E02 on a lazy spa?
Please follow these steps to resolve this:
- Remove the spa pump from the liner, with the stopper caps placed on the inside.
- Empty the spa fully of water.
- Remove the stopper caps and place a hose on the inside of the spa, up against the debris screen.
- Complete this for 5 minutes on each debris screen.
How do you clear a hot tub error code?
Turn your breaker back on without the filters in the spa. Did your error code go away? If it did, it is time to either deep soak your filters (about 48 hours should do the trick) and clean them really well, or, if they are older than 18 months, it is a good idea to replace them.
What does EO2 mean?
EO2
| Acronym | Definition |
|---|---|
| EO2 | Equipment Operator Second Class (Naval Rating) |
| EO2 | Engineering Aide Second Class (Naval Rating) |
How do I reset my Coleman Spa?
Turn the spa off, wait 30 seconds and turn it back on again. The controls will be reset. Plus, the custom settings you set in the previous step will be cancelled and the filtration will revert to the factory control.
How do you descale a hot tub?
Mix equal parts of vinegar and distilled water. Put the solution in a spray bottle. Generously spray the hot tub shell with the mixture. Let the mixture set for five minutes.
Can you repair a lazy spa?
According to the manufacturer, a Lay-Z Spa hot tub might deflate for one of two reasons either the air valve is loose, or the spa is torn or punctured.If the hot tub is punctured, repair it with the provided repair patch. Simply follow the manufacturer’s instructions to perform this uncomplicated job.
Why does my inflatable hot tub keep turning off?
First, check your water level. Then, look for clogs in your circulation system, and wash or change your filter.If the high limit switch shut your heater off because your water got too hot or you have air trapped in your lines, resetting the heater will get it going again.
What does CL mean on hot tub?
Current time of day
The Big List of Spa and Hot Tub Error Codes
| CODE | ERROR CODE DESCRIPTION |
|---|---|
| CL | Current time of day; system message, not an error |
| COL | Cool – water is 20°F below set point; system message, not an error |
| CoLd | Cold – water is 40°F or less; system should self-start the circulation pump and heater |
What does FL2 mean on a hot tub?
FL1/FL2. This code means any of the following: the flow switch is malfunctioning open (FL1) or closed (FL2), the filter cartridge needs to be changed or cleaned, or there is an air lock condition at the circulation pump intake.
What does HH mean on a hot tub?
HH Overheating
Your spa has detected an excessively high temperature at the sensor in the heater chamber. The hot tub is shutting down to protect users from dangerously hot water.
Why does my hot tub say error?
A hot tub flow error indicates that there is a problem with the flowing of water through the hot tub heater.The most common causes for this are a dirty or damaged filter, low water levels, air in the pipework or a faulty pump or sensor..
Why is my hot tub flashing error?
The water probably isn’t flowing fast enough through the heater causing the temperature to increase. DO NOT USE THE HOT TUB while these error codes are flashing as the water will be scalding hot.
Why won’t my lazy spa heat up?
Unplug the pump from the socket. Whilst the pump is unplugged press the thermal reset button in and hold for 5 seconds. Plug the pump back in to the socket. Set the pump to heat and allow for 5-6 hours of heating.
A spa heater has a high-limit reset button. A spa or hot tub provides a form of personal relaxation known as hydrotherapy.A spa heater may need to be reset if it has tripped or stopped working. Using the high-limit reset switch and checking all breakers and GFCI outlets can reactivate the spa’s heater.
How do I unlock my Coleman spa?
Unlock Operating Panel
- Press the “Time” button on your hot tub operating panel.
- Push the “Jets 1” button.
- Push “Set down.” A “0” will appear on the screen indicating that the operating panel lock is off. The lock symbol will also disappear from the display on the operating panel.
There are generally two “hard resets” in hot tubs, the GFCI, and the high limit reset. The GFCI pops if there is any type of electrical short (such as water getting into the heating element, the reset on that can be in one of three places.
How do I get rid of limescale in my hot tub?
Mix vinegar and distilled water in a 1:1 ratio, and pour the solution into a spray bottle. Thoroughly spray the solution on the hot tub shell. Let it sit for around five minutes. Use a nylon brush to scrub the surface and around the jets.
How do you remove calcium deposits from a spa?
If you notice the surface feels “gritty” from calcium build up, use a warm water / vinegar mix to break it down and leave the shell nice and clean. Avoid using household cleaning products on your hot tub interior as they will have a negative impact on your new water and your acrylic shell.
What can I use to remove limescale?
- Soak a rag or a cloth in vinegar or lemon juice and wrap it around your tap, making sure that all areas are covered.
- Secure it in place with an elastic band and leave for an hour.
- Occasionally squeeze the cloth to release more of the acid into the crannies of the tap.
- Remove the cloth and wipe away the limescale.
Contents