Connect the Touch transceiver electrical plug. Push fit the Touch transceiver into the boiler. Using a flat bladed screwdriver remove the back cover from the Touch thermostat and insert only 3 batteries. Immediately insert the fourth battery into the thermostat.
Can you control an ideal boiler from your phone?
You’re in control. The Ideal Touch Connect heating app allows complete control of your heating system anytime and anywhere from your smart phone and web browser.With over 40 time and temperature periods per week, the Touch app can handle even the busiest of lifestyles with ease.
What is ideal touch connect?
The Ideal Touch Connect Alexa app allows you to control your heating by adjusting the target temperature and changing the heat mode.
Why is my thermostat not communicating with boiler?
When you have a wired thermostat that does not properly control the boiler, the problem can either be due to a faulty wiring, a damaged component, or an outdated unit. In all 3 cases, you need to be able to access the inner components, so get ready to open your thermostat.
Can a boiler work without a thermostat?
Do you need a thermostat for your boiler? In short: yes. Your boiler thermostat is essential if you want to be able to control the temperature of your central heating and hot water. If, for some reason, you’ve got a broken boiler thermostat, we advise you get it looked at pronto.
How do you pair an ideal touch thermostat?
Hold the thermostat approx 2 metres away from boiler. Locate the gateway adjacent to the house wireless router and connect the supplied ethernet cable from the gateway to the wireless router as shown. Connect the Gateway power cable and 3 pin plug together, then connect the 3 pin plug to a convenient mains socket.
How do I reset my ideal combi boiler?
REsET PROCEDURE
To reset boiler, turn the mode control knob (D) to reset position and immediately turn knob back to required setting. The boiler will repeat the ignition sequence. If the boiler still fails to light consult a Gas Safe Registered Engineer or in IE a Registered Gas Installer (RGII).
How do you turn on the heating on an ideal boiler?
To switch preheat on or off, move the domestic hot water preheat knob (B) full clockwise and then return it to the required domestic hot water temperature setting. The boiler will operate periodically for a few seconds to maintain the domestic hot water heat exchanger in a preheated condition.
How do I change the battery in my thermostat?
Battery Replacement: Un-clip the thermostat from its cradle by sliding the thermostat upwards. Using a flat bladed screwdriver pop off the rear cover Replace batteries Refit battery cover Batteries should operate for approximately 18 to 24 months.
How good is an ideal boiler?
Ideal Energy Efficiency
Ideal manufacture some of the most energy-efficient boilers on the UK market. They have a SEBDUK rating A and save around 90% of the energy generated by the boilers. To put that in perspective, old boilers lose 35-40% of the energy they create.
What is the gateway on a ideal boiler?
The gateway provides connection to the internet, via an Ethernet cable plugged into the home’s router, and communicates with the boiler and thermostat via an 868MHz RF signal.
Why is my ideal thermostat flashing?
If a battery symbol is blinking, the display is blinking or the display is blank then replace batteries. 1. During normal operation light (A) is on for Hot water Operation.If less than 4 lights are on either the room thermostat is too far from the boiler or the batteries in the room thermostat need replacing.
How do I set the time on my ideal thermostat?
Press MENU. Press HELP & SETTINGS. Press CHANGE TIME. Set the time using the up and down arrows. Press DONE. 4 Page 9 9 Tap screen to wake up. Press MENU. Press HELP & SETTINGS.
Why is my ideal thermostat not pairing?
Check the batteries are inserted correctly. Replace the batteries in the thermostat. Make sure the target temperature is at least 1°C higher than the actual room temperature on the thermostat.Check the Touch thermostat is within range of the boiler transceiver.
Why is my boiler not firing up?
A boiler might not ignite due to various possible reasons insufficient pressure, blockage in the burner, faulty valves, frozen pipes etc. Sometimes, you can fix the problem on your own. In other cases, you don’t have any choice but to call an engineer.
What does it mean when your thermostat is not communicating?
If your furnace is not within shouting distance from your thermostat, use walkie-talkies to communicate.If the furnace does not make a sound, the thermostat is not sending a signal and needs to be replaced. Turn off the breaker to your furnace. Remove the cover from the thermostat to expose the wiring.
Where is my thermostat in my house?
The best place for your thermostat is on an interior wall, away from all the areas we previously discussed (direct sunlight, air vents, your kitchen, hallways, windows and doors). Ideally, it should be placed toward the center of your home.
Can I use any wireless thermostat with my boiler?
Can you connect a wireless thermostat to any boiler? The particular wireless thermostat you have will affect whether it can be connected to your boiler. In most cases, they are compatible with most modern boilers, including combi, system and heat-only boilers.
How does a Honeywell wireless thermostat work?
Honeywell wireless thermostats can improve the control over the temperature in a room by sensing the surrounding air temperature and adjusting the heating accordingly, creating an automatic system which naturally conserves energy.
Most modern boilers will have a reset button that’s located on the boiler’s display. This will be located near where the fault code is being displayed. As an example, the reset button on a Vaillant EcoTec will be flame with a line through it. This is the reset and ignition button.
How do I start my boiler?
Close the bottom blowdown valves, then open the upper drum vent valves. Start filling with soft water. Manually inject boiler water treatment chemicals including oxygen scavenger chemicals, so that the chemicals are added with the fill water. Once full to the operating level, open the fuel system and fire the boiler.
Contents