Camera Left/Camera Right – The direction of left and right in relation to the direction the camera is facing. Usually opposite the subject’s left and right. Check The Gate – Called out after a take that the Director is satisfied with, for the 1st AC to check the internal part of the film camera called the gate.
What does checking the gate mean in film?
And check the gate means to look literally at the gate of the film camera where the film passes in front of the lens to make sure there aren’t any hairs in there because if there’s a hair or dust it would scratch the film.
Why do they say check the gate?
Gate: When shooting on film, you’ll often hear the assistant director shout, “Cut! Check the gate!” This is to ensure that the camera and film is free of any impurities or blockages (a hair in the way, for instance) that would render what’s been filmed unusable or call for another take.
What does open gate on a camera mean?
In Open Gate mode, the ALEXA XT can record ARRIRAW at a resolution of 3414 x 2198 (1.55:1 aspect ratio). Vertically, that’s higher resolution then most 4K cameras today, which come in at 2160 vertical lines. The image can be scaled by only 20% for 4K finish, or 15% for Ultra HD finishing.
What does tails mean on a film set?
Tail – The end of a shot or a roll is called the tail. Tail Slate – Sometimes it is necessary to mark a shot at the end rather than at the beginning. When this is done it is called a tail slate.
What does closing the gate mean?
It means that they will not admit anybody to the flight who appears at the gate after the time given. The logical “gate” which admits you to the aircraft is closed and you can no longer go through it. This is just a way of saying “make certain you are at the gate 30 minutes before departure time”.
Who checks the gate?
Normally the assistant director will call out “check the gate” when the director is ready to move on to the next shot. The crew will wait until the focus puller calls out “gate is clean.” If the gate is not clean, it will be cleaned with orangewood sticks and canned air and the crew will take the shot again.
What does it mean to burn a location in film?
“Burned Location” – Any location (house, restaurant, park etc.) that will not allow filming due to previous unresolved problems with film productions.It also includes location maps, other production requirements, and information for the following day of shooting.
What does AKS mean camera?
AKS – Abbreviation for accessories. Often labeled on the boxes of camera equipment. Camera Left/Camera Right – The direction of left and right in relation to the direction the camera is facing. Usually opposite the subject’s left and right.
What is a camera gate?
A film gate is a piece of metal framing behind the lens that lets light into the camera. With cameras that hold physical film, a film gate holds the front face of the celluloid.
Is ARRI Alexa full frame?
This sensor mode is covered by full frame lenses, the ARRI Master Macro 100 and by some Super 35 lenses with expanders. The maximum frame rate is 90 fps. Since the entire sensor is recorded, surround view is not available and this mode has the highest data rate.
What does full gate mean?
Definition of full gate
: the adjustment of a water turbine to utilize its full capacity working at full gate.
What does strike mean film?
Set deconstruction is also known as the strike. Sets are deconstructed in order to build up the next scene, but complete deconstruction and removal from the stage of sets, props, costumes, lights, and sound equipment occurs when the show ends its run at the venue.
What does Window mean in film?
Windows is a term used to describe periods of time a certain type of media is allowed to screen your film. Traditionally, a feature film is first released in theatres, then on DVD and pay-per-view/video-on-demand (VOD) and finally, on broadcast TV.
What does Abbey mean in film?
Abbey Singer refers to the second-to-last shot at a specific film location. It was named after Abbey Singer (pictured above, far left), a famous production manager who would alert his crew two shots before the set needed to be collapsed.
What does gate time mean?
On departures, the gate time is the time at which the plane pulls back from the gate. The runway time for departures is the time at which it takes off and includes the time it takes for the plane make its way from the gate through the queue of planes waiting to take off.
What happens if you open a film canister?
Opening a film canister in the daylight, room light or anywhere that your film can be exposed can ruin your film or alter the images to be developed. If you are not prepared to develop the film once you open the canister there is little reason to open it, and you should simply leave the film in the canister.
What does it mean when a director says print?
Print. When the director yells print after the shooting of a particular scene, this means that the scene is good and it is to be kept. Another word for the term print is “Hold.”
Who pulls focus sets?
The first assistant camera (also called the 1st assistant camera, 1st AC, first AC, or focus puller) has one main job: they sit next to the camera during filming and operate the lens’s focusing ring. The role of the focus puller is to keep the right subject in focus throughout each scene.
How do I change the resolution of a gate in Maya?
To display the resolution gate and film gate, enable these options from the View > Camera Settings panel menu or from the Display Options of the camera Attribute Editor. The resolution gate represents the rendering resolution (the region to be rendered). The film gate represents the dimensions of the camera aperture.
How do I find a film location?
Contact your local government office or film commission for assistance. They can help find potential locations for your film. You can also look into location scouting websites for listings of available locations offered to filmmakers.
Contents