How Do I Adjust My Swann Camera?

How do you adjust a Swann camera angle?

Aiming the camera
You can use the included allen key to adjust the camera angle. To adjust the orientation, loosen the screw indicated by 1. This enables you to rotate the camera so no matter what direction it is facing, your images will be the right way up. To tilt up and down, loosen the indicated by 2.

How can I improve my CCTV image quality?

How to Enhance the Quality of Your CCTV Footage

  1. Choose a camera with the ideal resolution. The resolution power of a CCTV camera is measured in lines, and the higher the lines, the better the quality of the footage.
  2. Improve the lighting around the camera.
  3. Use infrared illuminators to improve night vision.

How do I change the zoom on my CCTV camera?

Find the zoom and focus screws located on the bottom side of the camera. While watching the monitor, use your allen wrench to slowly turn the zoom adjustment.

How do I change the resolution on my Swann DVR?

How to change the resolution of the recorder?

  1. Go and access the Menu then proceed to Display then Output.
  2. Change the Resolution– pick a resolution that matches the display they are using.
  3. Click Save – to save the settings.

How do I reset my Swann DVR to factory settings?

DVR16-8600 Hard Factory Reset

  1. Power off the machine, remove the power plug from the back of the unit.
  2. Take off all case cover screws located on the back and side of the DVR and remove the case.
  3. There will be a small black button on the motherboard located towards the front panel of the unit, take note of its location.
See also  What Was Google Called Before Google?

How do I change the melody on my Swann driveway alert?

To change the doorbell chime: 1. Press the Chime Select button on the back of the Indoor Alarm Receiver. The next chime is played. Keep pressing the button until you hear a chime you like.

What is the difference between PIR and motion?

As the name implies, motion sensors detect moving objects outside or even inside your home. They are often tied to lights, alarms, security cameras, and most recently, smart doorbells.PIR or Passive Infrared motion sensors are designed to reliably detect people, large pets & other large warm moving objects.

How do I set my Swann camera to record all the time?

Article Details

  1. Go to MAIN MENU > RECORD.
  2. Inside the RECORD menu, you should see the RECORD Setup and MOTION Setup.
  3. 3.In the RECORD SCHEDULE screen, make sure first that the CH option (at the top left) is set to ALL.
  4. Back on the RECORD SETUP menu, go down to COPY TO and make sure it says ALL, then click the COPY button.

What is the super password for Swann?

12345
The default, all-access username is “admin”, the default password is “12345”.

Can you put camera DVR in attic?

Do not place the NVR in areas such as an attic or unfinished basement where it may be exposed to extreme temperatures moisture, heavy dust or dirt.

Why does my Swann camera look blurry?

If the camera lens doesn’t concentrate the light into the right spot of the camera image sensor, the result is a blurry (out of focus) image.Rays of light come to the lens and are directed to the camera sensor and it must converge in the correct point otherwise the image gets blurry.

See also  Is Focus Pulling Hard?

Why is my Swann camera blurry?

Security cameras can be blurry because the lens might be out of focus, the lens may be dirty, water droplets on the glass dome are causing the light to reflect back into the lens, the cameras image sensor is defective or the camera might be a low-resolution camera which will look blurry compared to other high

How do I make security video clearer?

How to Clean Up a Surveillance Video

  1. Crop the video to only include one video feed and then expand that portion to fill the entire video frame.
  2. Crop out the time stamp from the top or bottom of the frame.
  3. Use a degrain filter to remove excessive noise from the video.

Why is my security camera blurry at night?

At night the security camera IR turns on to illuminate the are and “see in the dark”, this light sometimes is bounced on objects and comes back to the camera lens.In this case, the light is bouncing on the camera dome and it’s coming back to the lens thus causing the blurry or foggy effect you see only at night time.

How do I improve night vision on my security cameras?

The best way to improve a security camera’s night vision is to provide additional lighting to brighten up the area.

  1. Provide additional lighting to brighten up the area.
  2. Clean the camera’s lens or glass dome regularly to prevent light reflections.
  3. Choose the right camera for the area being viewed.

What does 30x optical zoom mean?

The 30x magnification range is nothing short of incredible, allowing you to zoom up to distant subjects while still maintaining the clarity that only optical zoom can provide.And by combining this function with Digital Zoom, up to 120x zoom* can be achieved without sacrificing image quality!

See also  Can I Upgrade My Swann Cameras?

What does 4x optical zoom mean?

The 4x Zoom means that beyond the 10x optical zoom, the camera will electronically jack it up another 4 times. However, it does so by blowing up the pixels and it can make the photos grainy.

What is the difference between digital zoom and optical zoom?

Optical zoom leverages the physical change in a lens to adjust the distance between camera sensor and subject, whereas digital zoom uses magnification technology to enlarge an area of an image (thereby compromising the integrity of the picture by cutting down on the megapixels).

How do I fix the resolution on my DVR?

Changing The Resolution On Your DVR

  1. Next, scroll down to Main Menu and left-click.
  2. Once you are in the Setting Menu, click the Display icon.
  3. In the Display Menu you will see a line in the middle of the screen labeled, Resolution.
  4. Here, you can change the output resolution of your DVR to the desired level.

How do I reset my ZOSI DVR resolution?

How to reset Zosi DVR to factory settings

  1. Click the floating “Main menu”
  2. Click the “Advanced” button.
  3. Click the “reset” button.
  4. Click “OK” to confirm.

Contents

This entry was posted in Smart Camera by Warren Daniel. Bookmark the permalink.
Avatar photo

About Warren Daniel

Warren Daniel is an avid fan of smart devices. He truly enjoys the interconnected lifestyle that these gadgets provide, and he loves to try out all the latest and greatest innovations. Warren is always on the lookout for new ways to improve his life through technology, and he can't wait to see what comes next!