Most modern thermostatic radiator valves are bi-directional so can be fitted on either the flow or return pipe of your radiator. However, it’s always best practice to fit the TRV on the flow pipe that enters your radiator.
Should TRV be on inlet or outlet?
The vast majority of new TRV’s are bidirectional and can be fitted to either the flow or return, but it is always good practice to fit them to the flow side. If a non bidirectional TRV is fitted on the return side it will create a vibrating sound as the water tries to flow though it.
Does it matter which way water flows through a radiator?
Pipes from one radiator lead to another and do not cross, so you orient the radiator the same way as the other radiators on the same floor are oriented. If you only have one radiator, you will need to get into your neighbor’s apartment to figure out which way the pipes are going.
Can you put TRV on one pipe system?
For use in conventional 1-pipe systems, where circulation through the radiator relies on gravity.
Does it matter which way round you plumb a radiator?
The Rad can only go one way up – the top has one position for the air vent and the other side blanked off. At the bottom of the radiator it has openings either side for the inlet and outlet. So the radiator can only go in one vertical orientation.
Does TRV go on Inlet?
Where Should I Fit a TRV? Many thermostatic radiator valves nowadays are bidirectional, and you can install them to either the flow or the return pipe of your radiator. However, we would advise you to fit the TRV on the pipe that carries water to your inlet valve the flow pipe.
What do arrows on TRV mean?
Until about 1995 all thermostatic radiator valves were uni-directional. They were made with a single-headed arrow which marked the direction of flow. They had to be fitted so that the water passing through them followed the direction of the arrow. This meant that they were normally fitted to the flow pipe.
Which way does my radiator flow?
Radiators flow in from the top hose (where the thermostat is often in line) and exit out the bottom back to the block. The water pump moves the water through the thermostat to the radiator.
Which is the return pipe on radiator?
A second pipe (called the ‘return pipe’) collects the cooled water from the radiators and carries it back to the boiler for re-heating.
Can a radiator be installed backwards?
A word about installation: It is possible to install an engine fan backwards.That is, if a correctly installed fan draws air through the radiator, an incorrectly installed fan still draws air through the radiator it does not blow air through the radiator. Here is a picture of a fan correctly installed on its drive.
How does water flow around a radiator?
Radiators work through a heat transfer process called convection. When water in the radiator is heated, the surrounding air is also heated up via convection and this hot air is then moved around the room as the air circulates.As the hot water flows through the system it starts to cool down.
How does flow and return work?
What Boiler Flow And Return Pipes Are. As your boiler heats up water, it’s pumped out and circulated around your central heating system; this hot water comes out of the flow pipe. The water then travels around your heating system and returns to the boiler via the return pipe.
Which side of a radiator should get hot first?
Your heating engineer will then turn the central heating on and note down the order in which the radiators heat up, those nearest the pump normally get hot first. If the pump is fitted inside the boiler then the radiator nearest the boiler normally heats up first.
How does a TRV valve work?
The TRV is a self-regulating valve that works by changing the flow of hot water into a radiator.When the room temperature changes, a capsule in the valve head contracts or expands, which moves a pin in the valve body causing it either to open or close.
Which pipe is the inlet on a radiator?
Radiator Valve Inlet Positions
Standard radiators (commonly known as compact radiators) typically have side valve inlets. These are located at the bottom of the radiator too but tend to allow access from the side only (horizontally).
Do TRV valves fail?
The most common problem with a TRV is that the valve sticks or catches. This means that they are either stuck open or closed.If you cannot get the plunger working again, then the valve has failed and will need to be replaced completely.
Should all radiators have thermostatic valves?
We recommend you fit a thermostatic valve on every radiator. But there’s no need to fit one in a room with a fixed room thermostat.
Do you need a lockshield valve?
A lockshield valve helps to balance out that radiator and ensure the whole system is in sync, with all radiators heating at the same rate. It is therefore every bit as important a valve as without the system being balanced, there is often little point adjusting an individual temperature valve.
Should radiator valves be open or closed?
When you take the temperature of your radiator and valves you’ll be making tiny adjustments.You close the first radiator’s valve and then open it gradually until you have reached the desired temperature. If your radiators are not balanced, it will be harder to achieve the desired temperature if they are already on.
What happens if flow and return are reversed?
If the pipes are reversed, the sensor will record the lower temperature and could compensate to make up the difference. This can result in unwanted noise, or overheating and inefficiency.
What are the two valves on a radiator for?
One valve accounts for the amount of hot water that enters the radiator. The other valve, referred to as the lockshield valve, balances the system by regulating how much heat the radiator gives off.
Contents