You could plane off an old finish, but it’s not worth the risk. Planer cutterheads can generate sufficient friction to soften such finishes as polyurethane, gumming up their knives. Instead, use a belt sander set to about half its maximum speed and an 80- or 100-grit belt to remove the old film finish, as shown above.
Can you use a planer to remove old paint?
Paint can be removed with a planer. If you set the blade deeper, you can achieve this effect, even if you don’t run it gently along the surface. To remove paint, you need to set your blades so they dig deep enough to reach underneath the layer or layers of paint you wish to remove.
Can I put painted wood in planer?
It is okay to plane most types of painted wood but the blades may dull faster. For safety and environmental reasons, planing painted wood with lead based or cementitious (waterproofing) paint is NOT RECOMMENDED.
Can I plane instead of sand?
Any hand tool enthusiast will tell you, hand planes produce a better surface with more clarity even after finishing.I tend to use scrapers and planes as the last step prior to finish mostly because it saves on sandpaper and creates less dust.
How much material can a hand planer remove?
An electric (hand) planer is a tool used to take off small amounts wood by shaving it off in increments. They usually have two or three blades to achieve this and the maximum amount of material that can be removed in a single pass is usually around 1/8″ (3/32″ typically).
Whats the difference between sanding and planing?
Whereas sanders are used to alter the finish of wood, a wood planer is used to even out wood to an exact thickness. Planers produce boards of even thickness.Each planed piece of wood can be used by itself or glued to other planed pieces for a thicker board or block.
Can you use an electric planer to strip paint?
You’re unlikely to notice any particular dulling effect from running painted surfaces through your planer. Some paints are made from harder pigments but they’re not common in indoor paints these days.
What can you do with a wood planer?
Woodworking jointers and planers are used to mill wood so they can be used to build furniture and other projects to correct dimensions. If your workshop doesn’t have a jointer to square up an edge or your wood piece is too large to fit through, you can use your planer to flatten both pieces of wood.
Can you plane old deck boards?
There should be no issue running pressure-treated boards through a planer, however, if you do a little housekeeping afterward. Give the planer a good blasting off with an air hose after you finish for the day to reduce the amount of PT sawdust left in the machine.
Does a planer make wood smooth?
The planer is a tool for woodworkers who require large quantities of planed stock and who elect to buy it rough cut. A couple of trips through a planer and smooth, surface-planed stock emerges, often at a fraction of the cost of the milled boards sold at your neighborhood lumberyard.
Is a planer necessary?
Most woodworkers know that you need both a planer and a jointer to get the most out of rough lumber (at least for power tool users). The jointer is used to flatten one face and square up one edge and the planer is then used to make the second face flat and parallel to the first.
What can I use instead of a planer?
- Use a table saw. If you’ve got a large board to plane, a table saw might be a good option.
- Use a router. You can use a router to substitute for a wood planer in a similar way to a table saw.
- Use a jack plane.
- Use a wide-belt or drum sander.
- Get out the sandpaper.
- Take it to a cabinet maker.
Are hand planers any good?
An electric hand planer is a great tool to have for handymen, craftsmen, DIYers, and many more. They can make a difficult job easy, and free up time that is better spent on relaxing after a job well done. If you are still using an old-fashioned planer, it is definitely time to get your hands on a buzzer.
How much does it cost to remove with planer?
Set the planer to remove about 1/32 in. and run a batch of 2x2s through. Reset the planer to remove another 1/32 in. and run them through with the opposite face up.
Which type of stock should never be run through the planer?
What should you avoid when using a jointer or planer? Do not cut stock that has loose knots, splits, defects or foreign objects (e.g., metal stone) in it. Do not leave the machine running unattended. Shut off the power and make sure that the cutting head has stopped revolving before leaving the area.
Does a planer sand wood?
Answer from Lee Grindinger: “A planer will remove stock much, much more quickly than a drum sander. A sander is built to sand. For surfacing you’d be using a very coarse grit and this means several grit changes to get to the smoothness you’re looking for in a drum sander.
What is the purpose of planing wood?
A wood planer helps you even out a piece of wood into a board with the exact same thickness everywhere. A correctly planed board is completely flat on both sides, eliminating rough spots or leftover bark.
What is a wood planer machine?
A thickness planer (also known in the UK and Australia as a thicknesser or in North America as a planer) is a woodworking machine to trim boards to a consistent thickness throughout their length.
How do I remove paint from wood?
There are three ways of removing paint from wood: sanding, using a hot air gun and chemical paint strippers. Sanding is best kept for small projects unless you want to hire an industrial sander to remove paint and varnish from your floor.
Can you plane hardwood flooring?
Go ahead and plane the boards,no problem. I used to plane heart pine flooring for a hardwood floor company. This was mostly old growth boards that were removed from homes. Original finish was shellac,then varnish years later.
Is a wood planer worth it?
If you really want to get into woodworking, a thickness planer is worth the cost. Once you have it, you’ll never regret the expenditure, because you’ll be in control of your stock thickness like never before.
Contents