Of course it’s not alright to use a 9V adapter for a 5V device. Why would we provide the voltages ratings if it didn’t matter? Only if the 9 volts is regulated by a 5 volt regulator like the 7805. This is a very common situation.
What happens if I use 9V adapter on 5V device?
In general, connecting a 9V supply to 5V device could damage it immediately, or in long term, but it is impossible to say without seeing the schematics of the device how much excess voltage it can handle. However, you are using USB devices, so the above does not apply.
Can I use a 5V power supply on a 9V router?
4 Answers. You cannot use that adapter because it is outputting more voltage than the original (12v vs. 9v). This has a likely chance of burning out one or more of the components within the router.
Can I charge a 5 volt battery with a 9 volt charger?
You need a voltage source of 4.2V to charge a li-ion cell. Inside the battery there is a Battery Management System (BMS) so for the 9V li-ion battery you need a voltage source of 8.4 Volts to recharge it.
Can I use 10V adapter for 5V?
NO! you cannot use a 10V charger instead of a 5V for your mobile. Since the mobile is rated to be used with 5V charger, using one with 10V can be hazardous and may also cause irreparable damage to mobile.
Can I use 6V instead of 5V?
The short answer is No. A 5V, 2A adapter gives 10W of power and the 6V,1A gives only 6W.
Will a 12 volt LED work on 9 volts?
6. Can I Power a 12V Strip With a 9V Battery? The answer is “Yes”. A 12V strip can run on a power supply a little lower than its required electrical voltage, like a 9V alkaline battery.
Can I use 9V battery for NodeMCU?
The output from the Voltage regulator is connected to the Vin pin of NodeMCU & GND is connected to GND. Hence you can power up the module using 9V/12V DC Adapter or by 9V Battery. On the other hand, if you don’t want to power up the NodeMCU using DC Adapter, you can use 3.7V Lithium-Ion or Lithium Polymer Battery.
What resistor do I need to drop 12V to 5V?
12v to 5v converter using a voltage divider:
Components required: One 12v battery, 1.8k resistor, 1.3k resistor, connecting wires.
Can I use 9V 1a for 9V 0.6 A?
NO! Your output voltage is wrong, which is the important part. You can safely use an adapter with the same output voltage, and a current (A/mA) rating equal or higher than the original.
Can I use a 6V adapter for 9V?
Yes you can! the thing is you need voltage regulator which converts 6V ,1.5 A to 9V , 0.6A, however this will drain battery faster it has many other reasons.
Can you use a 12V adapter for a 5V device?
The device will very likely burn out. In addition, depending on what the device is and the capacity of the 12V supply, connecting a 12V supply to a device rated 5V max could lead to a hazard – fire, explosion, etc. Mostly it will get damaged.
Can I charge 9V battery?
The 9V li-ion battery is made of two 3.6V cells lending it a nominal voltage of 8.4. To safely recharge it you need a voltage source of 8.4V.It will automatically stop the charging once each cell voltage reaches 4.2V and the battery is full. Next, this is how you charge a 9V NiMH battery with a 12V charger.
Can you charge a 9.6V battery with a 12V charger?
The answer is no, not directly. If the 12V battery is completely discharged, a 9.6 V battery connected in parallel to it, will put some charge into the 12V battery but no where near enough for the 12V battery to be fully charged.
Can you recharge a regular 9V battery?
Yes, alkaline batteries can be recharged. However, it is not considered to be cost effective and does have some risks. Recharging any battery can cause the production of gas within the battery. Since an alkaline battery is normally sealed, very high pressures can be created within it.
Can I power ESP32 with 9V?
The ESP32 has an onboard 3V3 Regulator (AMS1117 3V3) which is rated at 800ma and can take up to 4.8V DC as an input, so its not safe to power the ESP32 with 9V DC battery, never exceed 5VDC if you dont want to fry the onboard Regulator.
Can I use a 7.5 V adapter for 9V?
However if the device is relying on the regulated voltage from the adaptor and has no internal circuit to control or limit overvoltage, then that 9v adapter may damage your device. That said, there are 7.5v devices designed with tolerances wide enough that the 9v you provide it won’t make any difference at all.
Does ESP32 have a 5V pin?
You can inspect the schematic, there is no 5V level shifting for the GPIO. The only thing taking 5V is the usb connector, the CP21 usb to serial, and the LDO. The ESP32 is not 5v tolerant, you could not use the built in ADC to a 5V range. You could use an external ADC which operates on 5v.
Can I use 4.5 v instead of 5V?
It’ll work fine.
Can I use a 7.5 v adapter for a 5V device?
1 Answer. You should never use a significantly higher voltage rating adaptor on any kind of electrical device. If you do so you are risking damaging the equipment and anything else that you might have plugged into it.
Can I use 6V battery for 5V device?
You could convert the 6V adapter to 5V if you’re comfortable with electronic circuits. This can be accomplished by hooking up the output of the adapter to a simple 5V linear regulator, which will probably have a dropout of 200mA.
Contents