the correct answer is,yes,you need a transom saver. even though boats are designed to flex and move in the water,they are not designed to be rigidly mounted to a trailer with a motor bouncing on the back that is flexing and stressing the transom with every bounce.
What happens if you don’t use a transom saver?
A traditional transom saver attaches to the trailer frame and outboard. Evinrude outboards use a lock arm. Without a transom saver, a skeg can hit the pavement.
Does Lund recommend a transom saver?
Lund does not have a recommendation whether to have a transom saver or not.
How long should my transom saver be?
21” to 31”
You’ll probably want a transom saver that extends from 21” to 31” which gives many options to position your outboard optimally on the trailer.
Should you travel with your outboard up or down?
Generally, you should tow your boat with the motor down, especially if your trailer offers good ground clearance. Additionally, most manufacturers recommend that you should pull your boat down. However, you can choose to tow with the motor up if you desire ground clearance.
How long do transoms last?
Step 4: Fabricating the Transom
From the looks of the transom in this boat, I would estimate a typical transom will last about 20 years or so before they need to be replaced.
How much does a 9.9 motor weigh?
9 and F8, provide nimble, lightweight, efficient power you can take with you. These SOHC 212cc two-cylinder wonders are both under 90 pounds.
Specs & Compare.
Engine Type | 2 cyl |
---|---|
Fuel Induction System | Carb |
Weight † | 39 kg (87 lbs) – 42 kg (93 lbs) |
Recommended Fuel | Octane 87 |
Does Lund use wood transom?
No wood in transoms throughout the Lund line up. Its amazing that it took any boat company this long to figure out that wood as a component material was a bad idea. “WHAT MATERIAL IS USED IN LUND TRANSOMS? In 2017, select models have a composite transom.
What years did Lund have transom issues?
This is a common problem with 2000 to 2007 vintage Lunds. That was the end of the Genmar era before they were purchased by Brunswick. Unfortunately there is no warranty on these boats.
What can I use for a transom?
Most transoms are on the order of one and a half inches thick. If there is any curve to the transom, this thickness is best made up of two three-quarter inch or three half inch thick layers of plywood. You can use top-of-the line marine plywood or lumberyard exterior ply.
Can I start my outboard motor without water?
Starting a boat without water is not recommended. Most outboard and inboard engines use impellers (rubber pumps) to run water to the boat’s cooling system. Without water to cool off and lubricate, the impeller will heat up super fast and possibly damage.
Can a boat transom be repaired?
Repairing A Rotted Transom
One method is to use a product like Git-Rot from BoatLIFE. This two-part liquid epoxy fills and restores the dry rot inside the wood using capillary action to penetrate it without drilling it full of holes. You can inject Git-Rot directly into the wood for more thorough penetration.
How much does it cost to replace a transom?
How much to fix a wet transom. Repairing a transom is a laborious exercise that can range from $3,000 to $10,000 depending on the vessel size construction and tradesmen used for the task.
How do you test transom?
Look for any signs of transom bowing or deformation. Look for any signs of the motor mounting bolts and washers being pulled into the transom. If the customer knows his boat, he will not have any issues with you to tug up and down on the bottom of the motor with the motor tipped fully up.
Which is better 2 or 4-stroke outboard?
4-Stroke Outboards Pros
The fuel efficiency of a 4-stroke motor can be 50% better than that of a 2-stroke motor with the same HP. As for environmental concerns, 4 stroke outboards produce far less harmful emissions, which can be as much as 90% cleaner than those from a similar sized 2-stroke motor.
What is the smallest outboard motor with electric start?
New Mercury 9.9hp outboard the lightest in its class – with optional electric start. Mercury Marine is introducing a new 9.9hp TwoStroke outboard that is the lightest in its class – an ultralight, compact and portable engine which provides exceptional power.
What is the lightest 4-stroke outboard engine?
Introducing the lightest weight in its class, EFI 40hp four stroke. Outfitted with a sleek four stroke design and starting at just 209 pounds, you will not find a lighter weight motor in its class.
Is Lund a good boat brand?
Lund Boats are more expensive than most of their competitors’ boats, and most owners feel the boats are worth it. They are built from quality materials, backed up with a strong warranty. Their durability has been proven in fresh and saltwater, on rivers, lakes, and the sea.
Does Lund make good boats?
Lund boats have been around for over 70 years, and there are many advantages to buying a Lund boat. They are well respected for their aluminum boat construction, although they have also been building some fiberglass boats since the 1960’s.
Do Alumacraft boats have wood floors?
Between AlumaCrafts legendary Double Thick 2XB hull, Aluminum Transom, Aluminum Floor on all models, Aluminum Storage Lids that are twice as thick as competitors, Aluminum Storage floors and sidewalls, most companys even Premium Based brands that cost more use plywood floors, Plywood Transom, Plywood storage boxes and
When did Brunswick buy Lund?
2004
Lund Boats builds outboard aluminum and fiberglass fishing boats in New York Mills, Minn. The Brunswick Boat Group bought the company in 2004.
Contents