How Do You Set A Schlage Alarm?

To enable the alarm, simply press and hold down on the inside Schlage button for around five seconds. Release the button when it flashes. If you want to disable the alarm in the future, you’ll hold down the button until there are two flashes.

How do I reset my Schlage alarm?

Within 10 seconds, press and hold until lights green and the lock beeps. triggered, there is a built-in 3 second delay for it to reset. »If the alarm sounds, you can silence it early by pressing down on the Schlage button until the alarm sound stops.

How do I program my Schlage auto lock?

To get started, open your door and extend the deadbolt so that it’s in the locked position. From there, press the Schlage button at the top of the keypad and enter in your six-digit programming code. Once the programming code is entered, hit “9” on the keypad. You’ll get one beep and one blink of the green checkmark.

How do you program a Schlage Z Wave lock?

Complete the following steps to include your Schlage Z-Wave Lock:

1. Enter exclusion mode. Before you attempt to pair your Schlage Lock, you should clear it from the network first.
2. Clear the lock. Next you will activate the learn function on your Schlage Lock.
3. Pair the lock.
4. Test the lock.

How do I change the 4 digit code on my Schlage keypad?

Press the “Schlage” button and the number “1” button simultaneously to add/change a new entry code. Wait for the “Schlage” button to beep and flash three times. Enter a new four-digit code, and wait for the “Schlage” button to flash and beep three times. Re-enter the same four-digit code to confirm the change.

What does the Schlage button do?

Inside Schlage Button • Located on the inside of the door. Used to silence the alarm. Does not lock or unlock the door. Thumbturn • Used to lock and unlock manually from the inside.

Where is Schlage program code?

The default programming code is printed on a label on the programming guide that came with your lock. If you do not have access to the guide, remove the lock from the door and look on the back of the lock for a label containing the default code.

Why does Schlage lock beep?

The beeper is there to confirm a successful unlocking or locking of the smart lock when using the keypad, as well as confirming each press of a number. The alarm is there to ward off any undesirables from entering your house without your permission.

Why is my keypad lock beeping?

The lock should beep twice when it unlocks and once when it locks. It will also beep if there is a warning such as a low battery or a jammed bolt.Reinstall the battery cover.

Why is my door keypad beeping?

If your Electronic Door Lock is beeping and the buttons are flashing red, this means that there’s been some kind of error or the batteries are low. If the batteries have already been changed and you still see a red flashing light when you try to use the lock, there could be an error with the lock.

How do I change my 4 digit Schlage Lock code without programming code?

So first how to Reset Schlage Keypad lock?

1. Disconnect the batteries.
2. Press and hold the Outside Schlage Button.
3. While holding the Outside Schlage Button, Reconnect the batteries.
4. Release the Outside Schlage Button.
5. To check that the lock was reset, press the Outside Schlage Button and enter one of the Default User.

Why does Schlage lock blink red?

The Schlage button flashes red continuously. What does this mean? The battery is dead. You will need to replace the battery immediately.

How do I connect my phone to Schlage?

To pair your Schlage Connect Smart Deadbolt with Samsung SmartThings, open the SmartThings app on your mobile device and tap on Home. Under Things, choose Add a Thing and follow the directions in the app. At the end of enrollment, a green light on your lock indicates success.

How do I change my Schlage 6 digit code?

?To change the six-digit programming code? to one of your own choosing:

1. Enter the existing six-digit code.
2. Press the “Schlage” and then the “3” keys.
3. When three orange flashes and three beeps occur, enter a new six-digit code.
4. When three orange flashes and three beeps occur again, reenter the same new six-digit code.

How do you change the 4 digit code on a Schlage Lock be365?

Press the Schlage button and then press 3. Wait for the lock to beep three times and flash orange light times. Enter your new Programming Code and wait for the usual 3 orange flashes and 3 beeps. Re-enter the new Programming Code to complete the change.

How do keypad door locks work?

How Keypad Locks Work. Instead of a key, this type of lock system requires a numerical code to grant entry to a facility or property. The code is punched in by users via a numerical pad, similar to those on a basic calculator. If the correct code is entered, the door lock or deadbolt should release.

How do you change the battery in a Schlage lock?

The Schlage Connect™ Smart Deadbolt requires four new AA alkaline batteries, installed on the interior side of the lock. Remove the black battery cover on the interior side of the lock by sliding it up. Unsnap the battery connector (a short wire), remove the battery tray and replace the batteries.