A Rheem water heater leaves the factory with the temperature preset at 120 degrees Fahrenheit, but you can adjust the temperature on the thermostat anywhere from 90 degrees Fahrenheit up to 150 degrees Fahrenheit.
What setting should my Rheem water heater be on?
120°F.
Tank Water Heating
Residential tank water heaters typically store between 20 and 80 gallons of hot water hot throughout, usually at the factory setting of 120°F. The temperature can be adjusted up or down by a control on the unit.
Is 130 too hot for water heater?
Professionals recommend keeping your water heater set at a temperature between 130 and 140 degrees Fahrenheit. Any higher, or lower, could actually be dangerous for you and your family. While turning the temperature up higher can result in burns, turning it lower than the recommended setting can also be dangerous.
What should my hot water tank thermostat be set at?
120 degrees Fahrenheit
The short answer: 120 degrees Fahrenheit. This is the preset thermostat temperature in most new water heaters, and it’s the recommended setting of the U.S. Department of Energy. At this temperature, harmful pathogens like the kind that cause Legionnaires’ disease are prevented from multiplying and may be killed.
What does AB and C mean on water heater?
Generally, A means 120 degrees, B means 130 degrees, and C means 140 degrees.
How do you turn on a Rheem hot water heater?
How to Light a Rheem Water-Heater Pilot
- Rotate the gas knob on your Rheem water-heater clockwise until it is in the “Off” position.
- Rotate the water-heater temperature dial counterclockwise until it is set to the lowest temperature setting.
- Lift the outer door off of your Rheem water-heater.
Is 125 too hot for a hot water heater?
On the side of most water heaters, you’ll find a warning that says water temperatures of 125 degrees Fahrenheit can cause burns or death. To be safe, the water coming out of the plumbing fixtures in a home shouldn’t be any hotter than 120 degrees.
Is 120 too hot for water heater?
The EPA recommends 120 degrees because it’s hot enough to keep diseases at bay, it’s not hot enough to cause scalding, it will supply enough hot water for most small families and is relatively energy-efficient.
Can I set my water heater to 125?
If you invest in one or more thermal protection devices to protect against overly hot water, the water heater could be safely set a little higher than 125 degrees. Most water heaters don’t have a thermostat control that is calibrated in such a way that you can just dial in 125 degrees.
How do you adjust the temperature on a Rheem gas water heater?
Pull the insulation from the cavity behind the covers to expose the thermostats. Insert a small flat-head screwdriver into the slot on the thermostat dial. Rotate the thermostat to your desired temperature. Make sure to adjust both thermostats if your Rheem water heater has two access covers.
How long does it take for a Rheem water heater to heat up?
The average gas heater takes between 30 and 40 minutes to fully heat up the water in its tank. The average electric heater takes about twice as long as the average gas heater to fully heat up the water in its tank, so you can expect it to take between an hour and an hour and 20 minutes to heat up.
How do I reset my Rheem water heater?
Turn the water heater’s gas valve switch to the “OFF” position, wait for a few seconds and then flip the switch to the “ON” position to reset the system.
How do I reset my Rheem electric water heater?
Somewhere on your electric water heater, you’ll find a reset button. It’s usually red and often located near the thermostat. It may also be hidden behind a removable metal panel on the unitand then behind some insulation. Once you find the button, push and release it.
Is 115 too low for water heater?
Going too low creates the risk of bacteria growing in your pipes or water heater, but going too high leads to the danger of burning. To avoid either extreme, you’ll want to find a happy medium. We recommend always keeping the heater set between 110 and 120 degrees.
Will 115 degree water burn you?
Hot Water Safety. Even though a water temperature of 110° F is ‘relatively-safe’, exposure can be painful; the human pain threshold is around 106-108° F.A child can suffer a third-degree burn in 124°F water in less than three minutes. Children and adults can be burned this badly in two seconds or sooner in 149°F water
Is 150 too hot for water heater?
The recommended setting for household water heaters is not 150 degrees, but slightly less _ 140 degrees.Water temperatures higher than 140 degrees can burn the skin and are particularly dangerous for young children and the elderly.
How do I adjust the water temperature on my water heater?
Gas or electric water heaters
Find the access panel for the thermostat(s) and use a screwdriver to remove the panel. Peel back the insulation. Use a flathead screwdriver to adjust the thermostat up or down. If your water heater has two thermostats, adjust both the same amount.
Should hot water heater thermostats be set the same?
The majority of electric water heaters have two thermostats: an upper and a lower, located under two control panels. To ensure your electric water heater works as efficiently as possible, you should set both of the thermostats at the same temperature.
Is 60 degrees water hot?
In general, hot water is 130 F (54.4 C) or above. Warm water is between 110 and 90 F (43.3 to 32.2 C). Cold water is generally between 80 and 60 F (26.7 to 15 C).
Should water heater be set to on or pilot?
You should set the water heater to pilot. If, however, your water heater is also the boiler for your central heating, then you’ll want to leave the heating running as normal so that your house doesn’t get damp as a result of cold and condensation.
Contents