If your window frame is drywall rather than wood, or if your window frame doesn’t have wood behind the drywall, you should use drywall anchors. There is a hammer in style (pictured below) that might be included with your mounting hardware, or you can find a screw in style at the hardware store.
How do you anchor blinds?
Drill pilot holes where the screws should go, then drill the screws into place to secure the brackets. Install the blinds by sliding the headrail into the brackets. Close the brackets to secure the headrail into place. Attach the wand that rotates the blinds by hooking it to the metal clip at the top.
Should I screw blinds into window frame?
If the original wood window frame is still in place, you might be able to affix the brackets directly to the wood for an inside mount if you’re tight on space. You should not screw directly into the frame of the vinyl window.
What screws to use to mount blinds?
You probably need at least 1/2 inch of screw thread in wood for a safe hold on blinds. More is better. Remember that the plasterboard/plaster doesn’t count. Try to guage how thick it is (probably either 3/8 or 1/2 inch) and add that to the depth into the wood.
Do blinds need center support?
All blinds over 48 wide require the use of center support brackets – be sure to mount support bracket(s) in position(s) that will not interfere with the lift mechanisms.
Can I drill into a vinyl window frame to hang blinds?
Installing Blinds on Vinyl Window Frames
Never drill through the actual frame of the window but only drill through jamb extensions. If you plan to install them inside the opening you must ensure that the blinds’ bottom does not bang into the vinyl finger-hold located at the bottom.
Is it OK to drill into vinyl window frame?
In most cases, the simple answer to this question is ‘No‘. You should not screw brackets directly into the frame of the vinyl window as this can damage the functionality of the window.And if you are planning for outside mounting, then the brackets should be screwed to the outside opening.
How many brackets do I need for blinds?
Blinds over 95″ wide must have two support brackets spaced no more than 48″ apart. Blinds over 96″ wide or 114″ long require an additional support bracket positioned 7″ in from the cordlock or headrail. All bracket locations should be measured, marked, and the mounting holes drilled.
How do you keep blinds up?
If you want them to roll all the way up, you can just let go. However, if you want to stop the blinds partway up, let them roll up to just above where you want them. Then, lower the blinds back toward the window. Finally, tug the blinds down until they’re in the right spot and let them go.
Can I screw into vinyl?
Vinyl coated screws are great too.No matter which screw you buy, make sure it is a Phillips head screw because they are the easiest to use. Obviously, you want to be safe when climbing ladders to drill into the siding. Make sure that your ladder is secure and that the cord for your drill is clear of your work area.
How do you hang blinds without drilling holes?
How To Hang Blinds Without Drilling Holes
- Magnetic Blinds. The magnets at the back of these brackets make installation a rather seamless process.
- Tension Rods. Hang these blinds on a tension rod, which you can position inside your window trim.
- Command Strips.
- Self-Adhesive Blinds.
How do you hang blinds with command strips?
How Does Command Strip Blinds Work?
- Step 1:Wipe the surface clean with alcohol to clean off any dust or dirt.
- Step 2:Peel off the cover on the adhesive side.
- Step 3: Paste one on either side of the window and another on the middle.
- Step 4: Spread some strong glue on the side of the shade that will attach to the strips.
How do you hang blinds without brackets?
Place the head rail over the top window trim and center it over the window. Place a bubble level on top of the head rail and position the blind so it remains level on the top window trim. Mark the holes you drilled onto the head rail by placing a screw into each hole then pressing the screws into the wood.
Can you screw blinds into UPVC window frames?
It is perfectly OK to fit blinds directly onto uPVC windows.The first step is to position the brackets that will hold your blinds. Measure carefully to make sure the brackets are evenly spaced to give a neat appearance. Take a pencil and mark the holes where the screws to hold the brackets will go.
Can you install blinds on a window frame?
Inside mounted blinds and shades will give you the cleanest look. That is because they fit inside the window frame, and can be mounted as deep or as shallow as you like.You just mount the brackets outside of the window frame and hang your blinds or shades so they extend past the frame.