How Do I Reconnect My Hive To My Boiler?

How do I reconnect my Hive heating?

Hold the central heating button down on the receiver until the status light is flashing pink. Release the button and then hold it again until the status light is double flashing amber.

Why is my Hive not connecting to my boiler?

Lift your thermostat off the hooks that hold it against the wall and take your thermostat to the receiver which you will find near to your boiler/hot water tank. Remove the batteries and put them straight back in again. This will turn the thermostat off and on which should help establish a connection to the receiver.

How do I get my Hive back online?

You can reconnect the hub to your Wi-Fi by going to your Hive app, tap the Hub 360, Settings, Change Wi-Fi, and follow the in-app instructions. Step 6. Go back to ‘Menu’ in the Hive app, tap ‘Manage devices‘ then refresh the page. If the hub is showing as ‘connected’ you’re done!

Why is my Hive not connecting?

Check that your Hive hub is connected to the mains power socket and switched on. 4. Check any Signal Boosters (formerly known as SmartPlugs) you have are switched on and in the recommended location.For Hive Active Plugs check that the electrical device you have plugged into your Hive Active Plug is switched on.

How long does it take for Hive to reconnect?

This usually takes 5-10 minutes. Once the AMBER light is flashing, the hub is set up and you can move onto installing the receiver. If no lights are displayed immediately after the hub has been turned on, check all cables are connected and the power socket works.

Why isn’t my boiler firing up?

A boiler might not ignite due to various possible reasons – insufficient pressure, blockage in the burner, faulty valves, frozen pipes etc. Sometimes, you can fix the problem on your own. In other cases, you don’t have any choice but to call an engineer.

How do I reconnect my Hive to WIFI?

Log into the Hive app and tap your Hive Leak Sensor. When viewing the product page, tap the settings icon on the top right and then tap ‘Change Wi-Fi‘. You will be guided through steps to connect to your new network.

How do I reconnect my Hive thermostat to the Hub?

To connect the receiver to the hub, put the hub into pairing mode. You can do this by selecting ‘Install devices’ within the Hive app menu. From there tap ‘Add another device’ and then ‘Go’ which will start the hubs search. Leave the hub searching and the receiver will change to a single flash of amber.

How do I connect my Hive to WIFI?

Go to the Hive app and tap on the Hive Leak Sensor. The settings icon on the top right is where you can change the wi-fi on the product page. You will be led through the process of connecting to your new network.

Why is my boiler not responding to my thermostat?

When you have a wired thermostat that does not properly control the boiler, the problem can either be due to a faulty wiring, a damaged component, or an outdated unit. In all 3 cases, you need to be able to access the inner components, so get ready to open your thermostat.

How do I reconnect my hive after changing the battery?

Take out the old batteries and replace with fully charged ones – Hive thermostats take four AA batteries. Secure the thermostat back onto the wall mount – it should automatically turn back on and reconnect to the system.

How do you reignite a boiler?

How do you relight the pilot light on a boiler?

1. Turn the gas to ‘pilot. ‘
2. Press and hold the reset switch for one minute and hold a flame to the pilot light at the same time.
3. If all is working as expected, return any casing/doors and turn the gas from ‘pilot’ to ‘on.

How do you restart a boiler?

Follow these simple instructions to reset your boiler:

1. Refer to your boiler manual.
2. Push the reset button for 10 seconds.
3. Wait 2 – 3 minutes, the boiler should fire up.
4. Repeat twice if the first attempt fails.
5. If the boiler still fails to fire up on the third attempt, double check the gas supply.

Where is the reset button on the boiler?

Your boiler restart button, also referred to as ‘lock out’, is located on your boiler burner unit. Usually, the burner unit front door cover will need to be removed to gain access to the control box reset (when ‘tripped’ the button is normally illuminated).

Why is my Hive thermostat not connecting to the app?

Hold the central heating button down on the receiver until the status light flashes pink. Release the button then press and hold it again until the status light is double flashing amber. To reconnect the receiver to your hub, put your hub into pairing mode by selecting ‘Install devices’ in the Hive app menu.

How do I reset my hive hub UK?

The Hive Hub can be reset by pulling the power cable out and putting it back in again. It will take about 5 minutes to fully reboot and pair to your devices. After the 5 minutes, refresh the app or website.