Turn the gas knob to Pilot, press and hold it down. This will start the flow of gas so you can light the flame. Some water heaters have a separate button for pilot mode, usually a red one, which you’ll press and hold. While still holding the gas down, light that pilot.
What is pilot mode in water heater?
On gas water heaters, the pilot light makes sure that there’s always flame available when the burner needs to kick in and heat water. If you run out of gas, install a new water heater or have to shut it down for some reason, lighting the pilot is the first step to turn on a water heater.
Do I leave water heater on pilot or on?
3 Answers. Yes it is safe to leave the water heater in pilot mode while flushing. You do not want the burner to fire while the tank is empty as this can damage the tank but the pilot will not cause a problem. Added: most gas valves with a standing pilot have the temp setting and pilot then off settings.
How do you turn on a pilot light?
Turn the gas regulator valve to the pilot position. If the water heater has a manual ignite button, press that to light the pilot. If it doesn’t have the button, or the button fails, press the regulator valve and hold a grill lighter or long match to the pilot light valve until the pilot ignites.
How do I put my water heater on vacation mode?
If your hot water heater doesn’t have a vacation setting, simply manually adjust your temperature to resemble Vacation Mode by lowering the temperature to 50 degrees Fahrenheit, or the lowest setting your thermostat allows. You may also choose to turn your hot water heater off completely.
Do all water heaters have a pilot light?
* Caution: Most modern water heaters no longer use standing pilots. They use electronic ignition to ignite the gas. Do not attempt to manually light an electronic ignition system.
Should the pilot light always be on in a gas water heater?
The thermocouple’s job is to shut a gas safety valve if the pilot light goes out. That’s important because gas is always being supplied to the pilot to keep the flame lit. But if the pilot flame goes out, then the gas would still be released. After a while, the gas could collect in your home and become a health hazard.
How do you relight an automatic pilot light?
Press the gas control knob down all the way and hold it in the depressed position. If you have no igniter, move the match or barbecue lighter flame to the end of the pilot tube; the pilot flame should light immediately. If you have a spark igniter, press the ignition button until the pilot flame ignites.
Can I turn off water and leave water heater on?
You should turn off your water heater if the water is off only if your water is turned off for an extended period of time, like a vacation, and you have a tank-type or hybrid water heater. For short term shutoffs, you can leave your water heater on until the cold water starts flowing in again.
Should I turn off my water heater when not in use?
No, unless you’re going on vacation for a month or longer, you shouldn’t turn off your water heater. Here’s why: You won’t see significant energy savings. You’ll create more problems by turning your water heater off/on repeatedly.
What setting should water heater be on?
Professionals recommend keeping your water heater set at a temperature between 130 and 140 degrees Fahrenheit. Any higher, or lower, could actually be dangerous for you and your family. While turning the temperature up higher can result in burns, turning it lower than the recommended setting can also be dangerous.
What do I do if my pilot light won’t light?
If your pilot light won’t stay alight, it might be the thermocouple. Sometimes dust buildup collects on the thermocouple and blocks the sensor. Try cleaning the thermocouple and then relighting the pilot light. If it continues to go out, the thermocouple might need to be replaced.
What do I do if my water heater won’t light?
If you have a natural or propane gas water heater, chances are the pilot has gone out.If the pilot doesn’t relight, if it goes out right after lighting or if it goes out repeatedly, by far the most common cause is a bad thermocouple.
How do I know if my pilot light is out on my water heater?
When a water heater pilot light goes out, it usually means that a natural change in gas pressure extinguished the flame. The main sign that a pilot light is out is one that everyone dreads: The water won’t get hot.
How do you fix a pilot light on a gas heater?
Once the gas has had time to dissipate, turn the knob to “Pilot.” Then, hold down the “Reset” button and bring the flame of a long lighter close to the pilot light opening. This should light the furnace pilot light. Once you are sure the pilot light is on, release your pressure on the reset button.
Where do you light a pilot?
Step 1: Find the pilot light assembly. It’s usually near the bottom of the furnace and has a gas valve with on, off, and pilot settings. Step 2: Turn the valve to off and wait three minutes.
Can I leave my hot water heater on vacation mode?
If you turn your water heating system off while you’re away and water freezes into ice, you run the risk of cracks, damage to your plumbing, and possibly necessitating the entire replacement of your system.Setting the system to Vacation or Pilot mode saves energy while also preventing damage to your water heater.
How do I turn my water back on after vacation?
How to Turn Water Back on After Getting Air Out of the Pipes
- Allow all faucets and spigots inside and outside the home to remain open from one-quarter to one-third of the way.
- Locate the main water valve.
- Open all faucets and spigots another one-quarter to one-third of the way.
- Turn all the faucets off in the house.
Can you manually light a gas water heater?
Lighting a water heater is simple, no matter what type you have. Most newer models of gas water heaters have a simple ignition switch. In just a few steps the water heater is lit, no problem. If you’ve moved into an older house, though, you many have the kind of water heater that needs to be lit manually.
How do I know if my pilot light is out?
How to Tell If the Pilot Light Is Out
- Locate the front cover panel on your furnace. It should be a little door that’s easily visible.
- If your pilot light is on, it should be easy to see your eyes will be drawn to the little flame.
- If you don’t see a flame, your pilot light is out.
- If there is a flame, check the color.
Why does the pilot light on water heater go out?
Some of the most common reasons that water heater pilot lights go out include: A faulty thermocouple.Over time, thermocouples can begin to malfunction and shut off the gas supply to the pilot light even if it’s burning properly. A bent or dirty thermocouple.
Contents