How Do You Reset The August Bridge?

To perform a hard reset on your Connect, leave the device plugged in and hold the reset button down for 5 seconds, then let go. You should see a pulsating green light, which indicates that the device is back in set up mode. If you want to set up your Connect again, follow these set up instructions.

How do you reset a August lock?

In order to use it again, you will need to re-setup the device. Clicking this button will open a new guide that will provide you with steps to resolve your issue. Select the Settings Gear above the lock circle. Select Factory Reset.

How do I reset my August connect WIFI?

Open the August App and go to House Settings. Select the Doorbell or August Connect Settings menu. Scroll to Factory Reset. Select Reset Doorbell or Reset Connect.

How do I fix August connect?

Check that your wireless router is plugged in and powered on. Then, connect your Wi-Fi to a computer or other device to ensure it is working properly. Your Wi-Fi name and/or password may have changed. Reset the Connect by holding down the button for 3 seconds and set up again using the August App.

Why is my August flashing red?

A flashing red light on your Smart Lock indicates that your batteries need to be replaced. To resolve this issue, replace your existing batteries with a fresh set of 4 brand new AA Alkaline batteries.Instructions for changing the batteries in your August Smart Lock are available here.

How do I reset my electronic lock?

A factory reset will delete all codes associated with the lock.

1. Make sure the door is open and unlocked.
2. Press and hold the program button for 30 seconds using the SmartKey tool or a paper clip. You will hear one long beep.
3. Press and release the program button. You will hear one short beep.

Can you reset a smart lock?

1 Factory Reset
Slide up the cover to open the back of your lock, exposing the buttons beneath. Push and hold the reset button for 10 seconds, until the lock beeps.The lock has now been restored and is ready to be set up again.

How do I connect August to New WIFI?

1. Setting Up August Connect (Android)
2. Select Settings.
3. Select Your Lock in Lock Settings.
4. Select Set Up August Connect.
5. Select Begin Scan to Start the Connection Process.
6. Enter Your Wi-Fi Password.
7. The Connect is connecting to Your Wi-Fi Network.
8. Select Done.

How do I manually reset Google WIFI mesh?

How to reset a Google Wifi on the device

1. Unplug the Google Wifi unit’s power cable.
2. Begin holding down the reset button on the back of the device. Hold down the button on your Google Wifi device. Google.
3. With the button depressed, reconnect the power source.
4. When the unit flashes white, then blue, release the button.

How do you connect August lock to WIFI?

Finding Network Credentials

1. Open the August Home App.
2. Tap the Menu icon.
3. Tap Settings.
4. Tap Set Up August Connect.
5. Tap Begin Scan to start connecting to Wi-Fi.
6. Type in your Wi-Fi password.
7. The Connect will show that is connecting.
8. Tap Done.

How do I calibrate my August Smart Lock?

Smart Lock Needs Recalibration

1. Open the August App and navigate to the affected lock.
2. Select Lock Settings.
3. Scroll to and tap on Calibrate Lock.
4. Follow in-app instructions to recalibrate.

Why is my August app not working?

General Troubleshooting Steps
Make sure your phone’s OS is on the latest version and that your lock’s firmware is up to date. Stand near your Smart Lock and open the August App on your phone. Check that you can lock and unlock your door using the August App.

How do I put my August keypad in setup mode?

Once you receive the reset code, push the logo button on the Smart Keypad.
Follow these steps to put your Keypad into setup mode:

1. Open the August App and go to House Settings.
2. Select the Keypad to enter Keypad Settings.
3. Select Disconnect Keypad and then the blue DISCONNECT button.

Why is my August blinking green?

The Connect LED indicator should display the following: No Light (a few seconds) ? Connect is now pulsating green slowly. If after rebooting, the Connect flashes green rapidly, the reset failed and the Connect is attempting to reconnect to the last Wi-Fi setup.

How do I set up the August app?

To install your August Connect:
In the August App, go to the side menu (upper left), tap Set Up New Device. Choose Set Up An August Connect. Choose a lock with which to associate your Connect. When prompted, plug connect into an outlet near your door and then follow the in-app instructions.

Why is my keypad lock beeping?

The lock should beep twice when it unlocks and once when it locks. It will also beep if there is a warning such as a low battery or a jammed bolt.Reinstall the battery cover.

How do I reset my smart code door lock?

Hold the button continuously for 30 seconds until you hear a beeping sound and see the status LED flashing red. Press the program button once again until you see the status LED flashing green and hear two beeping sounds. The Kwikset SmartCode deadbolt has now been reset and ready to be set up again.

How do I unregister August lock?

Open the August App. Select the lock from your Keychain. Go to the Guest List. Select REMOVE SELF.

Do I need August connect?

Best answer: No. The August Wi-Fi Smart Lock has everything built inside and can connect to the Internet without a Connect Bridge. If you have an August Smart Lock or a Smart Lock Pro (Generation 1, 2, or 3), your smart lock will function locally via Bluetooth connection without a Connect Bridge.

How do I setup a wireless bridge?

Here’s how to do it.

1. Position the bridge. Place the wireless bridge within range of your wireless router’s signal, and also within a cable’s length of your wired devices.
2. Connect the bridge to your network. If your router supports Wi-Fi Protected Setup, or WPS, setup is easy.
3. Plug in network devices.

How do I update WIFI settings?

1. How to Change Your Wireless Router Settings.
2. Connect to your network wirelessly, or via ethernet.
3. Find your router configuration page.
4. Log in with the username and password.
5. Find the Wireless Settings page.
6. Set the new channel, usually with a dropdown menu.
7. Your router will now reboot.
8. Troubleshooting.