How Do I Reset My Vivint Security System?

Vivint Router – Restore Factory Defaults

1. Hardware: Press and hold the Reset button on the back of the router for 10-15 seconds, then release.
2. Software: In the Configuration Interface, go to the Advanced tab and under the Administration tab click Factory Defaults.
3. All LED’s will flash indicating the router is resetting.

https://www.youtube.com/watch?v=CeXhoQE9ii4

How do I reboot my Vivint system?

Tap Cameras, the tap on the camera you want to reboot. At the bottom on the page, Tap Reboot camera, and then Yes to confirm. The camera will take 1-2 minutes to reboot.

How do you reset a frozen vivint panel?

Ensure the device remains in this state for at least 30 seconds after which you have to put the battery back inside. Remount the side panel and plug the panel back into your wall. After 2-3 minutes, the panel should start working again.

How do I reprogram my vivint?

Factory Reset:

1. Remove the battery pack.
2. Press and HOLD the Program button.
3. Re-insert the battery pack (keep holding the Program button for 30 seconds). The lock should beep and the LED will flash red.
4. Release and press the Program button once more.
5. The lock will re-initiate the handing process (extend/retract the bolt).

Why is my vivint not working?

Log out of your mobile app and log back in.If your connection is good, but it isn’t working, delete and reinstall your app. If neither the app nor the account center is working, go to your panel and send a command to your door locks, thermostats, or lighting modules directly from the panel.

How do I reboot my Vivint panel?

Reboot your panel
Tap Displays, then tap on the panel you want to reboot. Tap Reboot, and then Yes to confirm.

Where is the reset button on the vivint panel?

Hardware: Press and hold the Reset button on the back of the router for 10-15 seconds, then release.

How do I get my Vivint panel back on?

Remove the screw at the top of your panel with a screwdriver. To remove the panel cover, push the two tabs on top and pull the cover out and down. Hang the panel cover on the back plate using the white safety strip. Don’t be alarmed if you hear beeping.

How do I reset my vivint glance panel?

Reboot the Glance Display

1. Tap the menu icon from the bottom right corner of the Glance Display.
2. Tap Devices.
3. Enter your 4-digit PIN.
4. Tap Displays.
5. Tap your Glance Display.
6. Scroll down and tap Reboot.

Does vivint panel reboot on its own?

Vivint’s control panel doesn’t require a manual resetting if the power failure lasts for more than twenty-four hours. Your settings will automatically reboot and reconnect to your smart devices.

How do I reset my vivint security code?

If you ever forget the password for your Vivint app or My Account, you can reset it by following these steps:

1. Go to My Account and click on Forgot password?
2. Enter your email address.
3. Click OK.
4. You will receive a reset password email from Vivint.
5. You will be routed to account.vivint.com to enter a new password.

How do I reset my vivint thermostat?

Factory Reset

1. From the Home screen, press and hold the SIDE button for three (3) seconds.
2. Press DOWN to highlight Installer, then press the SIDE button.
3. Press DOWN to highlight Reset, then press the SIDE button.
4. Press DOWN to highlight Reset, then press the SIDE button.

How do I reset my vivint screen?

Line up the BOTTOM of the panel to the backplate and snap it back in place. Replace the top screw and plug the panel back into the wall. After 10-15 minutes, the panel should finish powering on.

How do you play vivint again?

On the home screen, tap on the Cameras icon in the lower toolbar. Press the play button on the desired camera. Press the rewind button.

How do I reset my vivint DVR?

Unplug the Smart Drive for 30 seconds, then plug it back in. Wait a few minutes to see if the connection has been re-established.

How do I fix vivint app?

If you are having problems opening the Vivint Sky app, delete and reinstall it. If this does not work, contact our Smart Home Specialists for further assistance.

How do you reset vivint?

Press and hold the doorbell button until the light turns yellow. The camera will also say, “Release now to reboot”. Once you hear this, release the button.

How do I reconnect my Vivint panel?

How to connect a panel to wireless internet using the mobile app.

1. Tap on the Menu icon.
2. Tap on Device Settings.
3. Tap on the panel you want to connect to WiFi.
4. Tap on the Wi-Fi line.
5. Connect your panel to WiFi. Tap on the WiFi network you want to connect your panel to, and enter in the password.

What does reboot panel mean?

A system reboot means that the system powers down and then powers back on. No changes to the settings are made during this time. This should not be confused with a factory reset, which will default settings and clear zones. There are many reasons why a person might want to reboot their system.

How do I reset my vivint Sky Control Panel?

The factory reset button is placed on the backside of the panel. Press and hold the reset button for a minute, then release it. The panel will reset the system and activate the process again as usual.

Why is my Vivint panel gray?

The home screen of your Glance Display will be green if the system is ready to arm, and grey if it’s not ready to arm. The system is not ready to arm when there is a door or window open in the home.