Since you’re pressing the reset button, make sure you hold it until the base LEDs flash amber. Remove all devices in Settings, My Devices. Start fresh using the Add Device button on the Devices tab to add the base and sync the cameras. Be sure to only briefly press the base sync button – don’t hold it.
How do I sync my Arlo base station to my phone?
Exact steps are provided below.
- Launch the Arlo app on iOS or Android.
- Tap or click Settings > My Devices.
- Select your Arlo camera.
- Scroll to the bottom of the Device Settings screen, and tap or click Remove Device.
- From the Devices screen, tap or click Add New Device, and select your camera from the list.
How do you make Arlo base station discoverable?
Turn the base station on by pressing the On-Off button. Wait for the power LED and Internet LED on the front of the base station to turn green in about two minutes. If you’re using a single-LED base station, wait for the LED to turn blue. Your base station is connected to the Internet.
Why is my Arlo go not connecting?
Unplug your Arlo Go camera, remove the battery, reinsert the battery, and notice the camera LED behavior when the door is closed.If your camera is still offline, try moving it to an area with better mobile coverage. If that does not work, you might need to reset your Arlo Go camera and set it up again.
Sync the camera to the base station: If you are using an Arlo base station, press the Sync button on the side or on the back of the base station for about two seconds and then release the button.
Can I connect Arlo base station to WiFi?
When you first set up your Arlo camera, you have the option to connect the camera directly to your WiFi router or to an Arlo SmartHub or base station. You can use the Arlo app to connect directly to your WiFi router.
Why is my Arlo base station not connecting to my phone?
If Arlo still cannot discover your base station, check the color of the Internet LED on your base station:Make sure that your router is powered on and connected to the Internet. If the Internet LED lights green, perform a factory reset on your base station and try the installation process again.
Why is my Arlo base station blinking orange?
A blinking amber LED on the SmartHub indicates a camera is out of range. This could be due to range, or poor signal due to interference. If your cameras are working, this may not cause an issue for you but could result in inability to stream the cameras.
How do I resync my Arlo camera base station?
Sync the camera to the base station: If you are using an Arlo base station, press the Sync button on the side of the base station for about two seconds and then release the button. Note: If you press the Sync button on the Arlo base station for too long, the LED under the USB symbol blinks amber for 10 minutes.
How do you reset Arlo base station?
To perform a factory reset on your SmartHub or base station:
- Use a pen or straightened paperclip to press and hold the Reset button on the back of the base station for about 10 seconds.
- When the Power and Internet LEDs are both solid green, tap the Arlo icon on your mobile device and log in to your Arlo app.
Does Arlo base station need to be connected to router?
Each base station must be connected to your router using an Ethernet cable. Note: You can also connect an Arlo or Arlo Pro base station to a WiFi extender if the extender has an available Ethernet port.
Why does my Arlo base station keep going offline?
Your camera might go offline if metal objects or thick walls and ceilings exist between the camera and the base station. Do you have an access point or other WiFi device close to the SmartHub or base station? If so, your Arlo system might be experiencing WiFi congestion.
What does the blue light on Arlo mean?
Ususlly the blinking blue led on the camera means that the camera is trying to sync with the base station if it is blinking slowly and a rapidly blinking blue led means that it has synced. It should go off after a couple of seconds once it has synced. Are your cameras working normally? You may have a range issue.
What does resetting Arlo base do?
WARNING: Performing a factory reset returns your Arlo Base Station or SmartHub to its default settings. Factory reset deletes your base station and all connected products and cameras from your Arlo account. After a factory reset, you must complete setup again.
How do I connect my Arlo Pro base station to the Internet?
Turn the base station on by pressing the On-Off button. Wait for the power LED and Internet LED on the front of the base station to turn green in about two minutes. If you’re using a single-LED base station, wait for the LED to turn blue. Your base station is connected to the Internet.
Can I use Arlo without an Internet connection?
Most Arlo cameras do require an active internet connection, as their cameras and systems are designed as an online, cloud based system. Having said this, some local (SmartHub/SD card) recording is possible, plus the Arlo Go doesn’t require WiFi access.
Can Arlo cameras be used without WiFi?
The Arlo Go Mobile Security Camera is ideal for security monitoring when traveling or in areas with limited or no WiFi access. Arlo Go works wherever there is 3G/4G LTE wireless connections.Get instant motion or sound detection alerts using the free Arlo app.
Contents