How Do I Change The Code On My Weiser Lock?

How do I change the code on my Weiser keypad lock?

Note: Programming instructions can also be found on interior of lock.

1. a. Press the program button on the interior unit once.
2. b. Enter in 4 to 8 digit code onto the keypad.
3. c. Press the “LOCK” button to save code.
4. d.
5. a. Press the program button on the interior unit twice.
6. b.
7. c.
8. d.

What is master code for Weiser lock?

0-0-0-0
The lock is programmed with the default mastercode 0-0-0-0. Replace this with a code of your own. The mastercode must be 4-10 digits. Keep door open and unlocked during programming.

How do I change my SmartCode lock code?

To set a code for the second user, press the SmartCode “Program” button twice to program a security code for the second user, such as a relative. Enter a four to eight digit security code on the outside electronic lock keypad and press the “Lock” button again.

How do I remove the code from my Weiser Smart lock?

Deleting User Codes

1. Press the program button.
2. Press the lock button.
3. Enter user code to delete.
4. Press lock button.
5. Re-enter user code to delete.
6. Press lock button.
7. If successful, the keypad will flash green once and you will hear 1 beep (if switch #3 is on).

How do I reset my Weiser Powerbolt 2 code?

Press and hold the “Reset” button for 5 seconds. You will hear 3 long beeps after the 5 seconds is completed indicating the lock has been reset. A User Code is used to unlock the door while a Mastercode is a password for making changes to the lock features.

How do I reset my Quickset lock code?

Hold the button continuously for 30 seconds until you hear a beeping sound and see the status LED flashing red. Press the program button once again until you see the status LED flashing green and hear two beeping sounds. The Kwikset SmartCode deadbolt has now been reset and ready to be set up again.

How do I reset a Quickset lock?

1 Factory Reset

1. Open your door.
2. Extend the latch bolt.
3. Slide up the cover to open the back of your lock, exposing the buttons beneath.
4. Push and hold the reset button for 10 seconds, until the lock beeps.
5. The light ring will flash red, then spin amber.
6. The lock has now been restored and is ready to be set up again.

How do you change the 4 digit code on a Kwikset lock?

Manually put the bolt in the extended (lock) position. Press the PROGRAM button once, enter your new 4 – 8 digit code and then press the LOCK button. 2. Press the PROGRAM button twice, enter the same or a new code and then press the LOCK button once.

How do I reset my Weiser Powerbolt?

How to restore default settings on my Powerbolt 2? Perform a factory reset

1. Make sure the door is open and unlocked.
2. Enter the default Mastercode (O-O-O-0).
3. Press the lock button.
4. Press 0.
5. Press the lock button.
6. Test the lock: With the door open and unlocked, Press the lock button.

How do I reset my Weiser Powerbolt 1?

How to Reset the Lock

1. Make sure the door is open and unlocked.
2. Press PROG -(for 30 seconds). You will hear 1 long beep.
3. Release PROG button.
4. Press PROG again.
5. You will hear 3 long beeps.

How do you use a Weiser keypad?

keyless entry- lock or unlock at the touch of a button.

1. The door is now locked. To unlock the door, touch the.
2. SecureScreen^™ Touch the numbers in any order. to display the full touchscreen.
3. Enter your code. Enter the access code.
4. Wrong code. Enter the access code.
5. The door is now unlocked. Tap the lock button to start over.