How Do You Get Rid Of Smelly Well Water?

To fix well water that smells bad, use one of these approaches:

1. Aerate water and/or inject air or oxygen.
2. Chlorinate well water to eliminate both sulfur and bacteria.
3. Use ozone gas in a closed tank or atmospheric tank.
4. Inject hydrogen peroxide.

How do you get the smell out of well water?

Shock your well with chlorine bleach or hydrogen peroxide to get temporary relief from sulfur odors. Often keeps odors away for 1 – 2 months. 2. Chlorinator: Install a chlorine injector system (chlorinator) on your wellhead for continuous injection of chlorine when the water is running.

How do you get rotten egg smell out of well water?

Chlorine bleach can effectively remove medium to high levels (over 6 mg/l) of hydrogen sulfide. The chlorine in the bleach chemically reacts with (oxi- dizes) the hydrogen sulfide eliminating the “rotten egg” odor. Chlorine bleach also reacts with iron or manganese, and disinfects water supplies.

Why does my well water stink?

What Causes the Sulphur Smell in Well Water? The main reason for the smell is sulfur bacteria or hydrogen sulfide. Sulfur bacteria are found in environments that lack oxygen, like deep wells.In all these cases, you’ll see hydrogen sulfide gas production that causes the sulfur smell.

Why does my well water smell like sewer?

If your cold well water smells like sewage, it can be the result of several causes: Hydrogen sulfide from iron, sulfur or other types of bacteria naturally occurring in your well water. Contaminated pipes with layers of bio-film caused by various types of iron, sulfur, or other types of bacteria.

Can I pour bleach down my well?

Mix 2 quarts bleach in 10 gallons of water; pour into well. Connect a garden hose to a nearby faucet and wash down the inside of the well. Open each faucet and let the water run until a strong chlorine odor is detected, then turn it off and go to the next one.Pour it into the well without pumping.

Can you put bleach in well water?

Mix the bleach with the well water.
? Attach a hose to the nearest outside faucet and allow the water to run onto the ground for 1-2 minutes until you smell chlorine. Then place the hose in the hole where you poured the bleach, allow the water to run back into the well for 15-20 minutes.

How much bleach should I put in my well?

4) Work out how much bleach will be needed: For every 50 gallons of water in the well use one quart of laundry bleach – (4 quarts in a gallon). Do not use excessive amounts of bleach – more is not more effective. 5) For best results the bleach should be combined with water before adding it to the well.

How do I get the sulfur smell out of my house?

Baking soda is well known for erasing odours. And the best thing is that it’s very easy to use and efficient too. If the smell is coming from your clothes then, soak them in baking soda before washing. You can also sprinkle baking soda in all the corners of your house to get rid of the sulphur scent.

Will a water filter remove sulfur smell?

Regardless of the source of the odors, installing whole house water filters that will remove hydrogen sulfide and kill sulfur bacteria is a good solution to consider if you want to reduce bad smells, and protect your family from other chemical and microbial contaminants.

Is smelly well water safe?

The smell of sulfur or even a chlorine odor may not necessarily indicate that your water is unsafe to drink. However, if you do find that the scent, taste or appearance of your drinking water has noticeably changed, it’s important that you have it tested to discover the source of the issue.

How long does it take to flush chlorine from well?

Monitor the process, it can take 30 minutes to 24 hours or more to flush all of the bleach solution from the well. Use chlorine test papers to verify that the water coming from the outside faucet or yard hydrant is clear of any bleach solution.

What does it mean if your water smells like rotten eggs?

hydrogen sulfide gas
In some parts of the country, drinking water can contain the chemical hydrogen sulfide gas, which smells just like rotten eggs. This can occur when water comes into contact with organic matter or with some minerals, such as pyrite. The situation mostly occurs as groundwater filters through organic material or rocks.

Can I put a chlorine tablet in my well?

Pool chlorine tablets can be used in wells. Ground wells require maintenance just as other household components and one of the most important tasks is disinfecting it.Because the tablets may sink to the bottom without completely dissolving, you must use them in combination with liquid chlorine.

How do I clean my well water?

CLEAN: Remove all loose or foreign debris from the well house, spring house or storage tank. Turn the pump circuit breaker off and remove the well cap or cover. Then scrub the accessible interior surface with strong chlorine solu- tion (1/2 gallon chlorine bleach per 5 gallons clean water).

How often should you chlorinate a well?

every 3 to 5 years
Homeowners with private wells should have their well water tested every 3 to 5 years for some contaminants, including bacteria. If these tests turn up positive for bacteria, chlorinating the well may be a way to resolve the problem.

How much does it cost to disinfect a well?

To disinfect your well and eliminate the bacteria, you should chlorinate the well. You can hire a company that services wells to do the chlorinating. The cost ranges from $80 – $200.

What is a natural way to clean well water?

Liquid chlorine in the form of household bleach and food grade white vinegar can be used to disinfect your well. When chlorine is added to water the pH level will rise. Food grade white vinegar is used to lower the water’s pH level so the chlorine will work effectively.

Should I put Clorox in my well?

Disinfecting Your Water
You can disinfect your well with household chlorine bleach such as Clorox, Purex or a generic brand. The chlorine in the bleach kills bacteria. Note that it may take more than one chlorination for your well to return a satisfactory test.

How do you flush chlorine out of a well?

Use ordinary liquid laundry bleach to shock chlorinate the water system. Determine how much bleach to use, then pour the bleach down the well and circulate it through the whole water distribution system. Wait 6-12 hours for the chlorine to work, then flush the chlorinated water from your well and pipes.

Should I shock my well?

Wells should be shock chlorinated when a well water sample result shows that there is bacteria in the water. Any time a well is opened for repair it must be disinfected. Newly-built wells should also be shock chlorinated following construction.