To add a thermostat, door lock, or module to your system, complete the following steps:
- Go to your touchscreen panel and touch the home button.
- Tap Services.
- Tap the wrench icon.
- Enter your 4-digit PIN.
- Tap Add Devices.
- At this point, go to the device you want to add (door lock, thermostats, light module, etc.).
Does Schlage connect with Vivint?
Technically, Vivint may well work with any Z-Wave enabled lock, but it specifically uses Kwikset Z-based locks. So you may want to try Yale, August, and Schlage Z-Wave enabled locks.
Can I add my own devices to Vivint?
In conclusion, while Vivint does not allow users to use their own, third-party camera’s to the home security system, you still have the freedom to connect additional smart devices, like a smart door lock.
How do I add Schlage lock to Zwave?
More videos on YouTube
- Enter exclusion mode. Before you attempt to pair your Schlage Lock, you should clear it from the network first.
- Clear the lock. Next you will activate the learn function on your Schlage Lock.
- Pair the lock. Next you will pair the lock with the Z-Wave network.
- Test the lock.
What is the installer code for Vivint?
2203 is the default installer code on the Vivint security system.
What app do I use for Schlage connect?
The free Schlage Home App for Apple iOS and Android lets you control and monitor your lock from anywhere using your smartphone. The app guides you through the setup process and puts complete access and control of your Schlage smart locks at your fingertips. Peace of mind in the palm of your hand.
How do I add a thermostat to my Vivint panel?
To add a thermostat, door lock, or module to your system, complete the following steps:
- Go to your touchscreen panel and touch the home button.
- Tap Services.
- Tap the wrench icon.
- Enter your 4-digit PIN.
- Tap Add Devices.
- At this point, go to the device you want to add (door lock, thermostats, light module, etc.).
How do you add sensors to vivint?
There’s a wizard in the Vivint SkyControl Panel that walks you through setting these up. Go into Settings > Devices > Add new Device, choose Sensor, and then remove the battery tab on the Window Sensor. It’ll pair immediately, then it’ll have you test it by pulling the magnet away from the sensor.
Can you have 2 vivint panels?
Users can have up to four of the Vivint Secondary Panels installed, in a customized configuration that best addresses the needs of each unique situation.
What hub do I need for Schlage Connect?
Pair your Schlage Connect with Amazon Alexa
To make this all work, you’ll just need a Wink Hub or Wink Hub 2, Wi-Fi connection and an iOS or Android smartphone device.
What Hub works with Schlage Connect?
4. Sync with a smart home automation hub. To access your lock remotely from your phone or with voice commands, you’ll need to sync it with a compatible smart home hub. The most common hubs for the Schlage Connect lock are Samsung SmartThings, Ring Alarm, Nexia and Wink.
Where is QR code on Schlage Connect?
on
The codes are located on the back of this guide and on the back of the inside assembly. You need to remove the inside assembly to see the label. 3. Your lock will enter a setup routine.
What is the programming code for Schlage locks?
Find the Default Programming Code
You can find your Schlage Lock Programming Code on the front of the user manualusually printed on a white label. If you don’t have the user manual, remove the lock from the door to find the Programming Codeprinted on a white label on the back of the keypad assembly.
How do I add Z-wave to Vivint?
At the Vivint panel, press the Home button, then select the three dots in the bottom right-hand corner of the panel. Select Software Version and enter the 4-digit code that appeared in Site Manager after unlocking the Installer Toolbox. Select Smart Home Devices > Z-wave > Add Node. Turn on the physical light switch.
How do I unlock my Vivint installer toolbox?
Property staff have the ability to unlock a unit’s Installer Toolbox at any time in Site Manager. If troubleshooting requires that you use a PIN, find the unit in Site Manager, select the unit options, and unlock the Installer Toolbox.
How do you reset Vivint without code?
Hardware: Press and hold the Reset button on the back of the router for 10-15 seconds, then release. Software: In the Configuration Interface, go to the Advanced tab and under the Administration tab click Factory Defaults. Then click the Restore Factory Defaults button.
Does Schlage connect work with Schlage Home app?
The free Schlage Home app for Apple iOS and Android is your remote control if you have a Schlage Encode Smart WiFi Deadbolt or Schlage Sense Smart Deadbolt. If you have a Schlage Connect Smart Deadbolt, you will need to use one of our partners’ apps like the Nexia or Samsung SmartThings app.
How do I connect to Schlage WiFi?
It’s easy to set up plug it in within Bluetooth range of the lock (usually about 40 feet), and use the Schlage Sense app to connect the Adapter to your home Wi-Fi network. Then pair it with your lock.
How do I connect my Schlage sense to my Iphone?
How to set up your Schlage Sense Wi-Fi Adapter for iOS
- 1Navigate to the menu in the app and click Wi-Fi Adapters.
- 3Type in the programming code located on the back of your Wi-Fi Adapter.
- 5Follow instructions on the screen to join the Wi-Fi Adapter’s temporary network, then return to the app to finish the setup.
How do I set the temperature on my Vivint thermostat?
Learn how to adjust the temperature on a smart thermostat from the Vivint Smart Home app.
- Tap the Temperature icon from the bottom menu.
- Adjust the temperature by tapping the plus or minus icons or by sliding the heat or cool temperatures around the circle.
How much is the Vivint element thermostat?
How Vivint Element Smart Thermostat compares
| Vivint Element Smart Thermostat | Ecobee4 | |
|---|---|---|
| Equipment cost | $169.00 | $246.51 |
| Monitoring fee | Yes | No |
| Professional installation required | Yes | No |
| Learn more | View on Vivint | View on Home Depot |
Contents