How Do You Use A 4 Pin Led Connector?

This connector is made from PBT firproof material, it protect the led strip from fire.

Installation Instructions:

1. Open the clip on the side.
2. Slid the 10mm LED light strip inside the clip underneath the two contact prongs.
3. Make sure the side of the strip aligns with the “+ -” polarity.
4. Close the wire clip.

What are the 4 wires on LED strip?

RGB strip light has a 4-wire connection, where green, red and blue are for the green, red and blue LEDs, and the black/white wire is the common +12V connection.

How do you connect LED lights after cutting?

A: If the LED light strip you purchased can be cut, the remaining part that you have cut off cannot be used anymore. If you want to reconnect them after cutting, you must use an additional 4 pin connector to reconnect.

What do you need to connect LED lights?

There are two main ways to connect LED strip lights together. They consist of a gapless pin connector and a jumper connector . Each allow you to connect two sections of low voltage strip lights together without soldering.

Can I connect two different LED light strips together?

You can connect different brand LED light strips to each other, providing they have the same voltage. Suppose you try to connect two strips with different voltages. In that case, they simply won’t work due to different voltage requirements for each strip, and you risk damaging them – a waste of money.

How do you connect LED lights to mains UK?

To get your strip light working, connect the transformer / driver to the strip light ( extending the cable with 2 core flex if necessary). Then you connect your transformer / driver to the mains via a plug or direct to the mains and you’re away.

Why is my LED remote not working?

If your remote control suddenly stops working or your lights start blinking, you may need to reset the controller and pair it back to the receiver unit.Remove battery from controller and then reinstall. Plug power supply and LED strip back into the receiver unit (Figure 2) Reconnect power supply to power.

How do LED controllers work?

RGB LED controllers work on a much simpler principal. They alter the power on each of the three channels (red, green and blue) to create a specific colour mix. To generate a purple colour, for example, the red and blue channels would be wound up, and the green channel turned off completely.

Can LED strips be hardwired?

When hardwiring the strips, you will just need to make solid connections between all your strip wires to the output wires on the power supply. This can be done with wire nuts or wiring all strips to a common positive and negative wire so you can make a one to one connection with the hardwired power supply.

Can LED strip lights be wired into mains?

Most — if not all — LED strip lights can be powered by the mains power supply.

Will LED lights work if you cut them?

Due to their design, LED Strip Lights will continue to work even after they have been cut. This is because their circuit is completely closed at each cutting point. If you are removing a section from the end of your strip light, always make sure you are cutting it at the end away from the connector.

Why are my LED lights not working after I cut them?

Yes, LED strip lights will carry on working after they‘ve been cut as long as you cut along the designated lines.Cutting elsewhere on the LED strip will cause that circuit, and potentially the whole strip, to cease working.

How do cut LED lights work?

LED strip lights are designed to be easy to cut apart with a pair of scissors. Each LED has a pair of copper dots at the end. As long as you cut between the dots, all of the LEDs will work. From there, you can connect the LEDs to a power source either through a quick connector or by soldering.

How do you attach LED strips to a wall?

Use your hands to mold a strip of putty to the desired shape and then push it onto the back of your LEDs. The strip can then be adhered to the designated surface. Alternatively, you could use cable ties to affix your LED strips to an object.

Where should I put my LED lights in my room?

To level up your light design, try installing LED strips in these five places around your home.

1. Under cabinets. As the name implies, under-cabinet lighting illuminates areas underneath your cabinetry.
2. Along toe kicks.
3. Under shelves.
4. Under the bed.
5. Behind computer and TV screens.

Do you put LED lights on the ceiling or wall?

We recommend having the lights go up your wall, but if you prefer to start the line of lights from the top of your wall, you will need LED strip clips to help hold up the power supply against the wall.

Do LED lights need to be plugged in to work?

Do LED Lights Burn Out?LEDs draw very little power so they can run for a long time on a small battery without any issues. There is no need for a bulky wall transformer and a wall plug to light your project.

How long of LED lights do I need for my room?

To determine the needed lumens, you will need to multiply your room square footage by your room foot-candle requirement. For example, a 100 square foot living room, which needs 10-20 foot-candles, will need 1,000-2,000 lumens. A 100 square foot dining room, which needs 30-40 foot-candles, will need 3,000-4,000 lumens.