How Do I Reset My Electronic Door Lock?

How to restore default settings on my Signature Series or SmartCode Deadbolt? Perform a factory reset

1. Remove battery pack.
2. Press and HOLD the Program button while reinserting the battery pack.
3. Press the Program button once more.
4. Perform the door handing process again to teach the lock the orientation of the door.

How do I reset my electronic lock?

How do I reset a code on my Powerbolt?

1. Insert functioning key & turn 1/4 turn clockwise.
2. Insert & remove the SmartKey learn tool. Remove functioning key.
3. Insert new key & turn 1/2 turn counter-clockwise. Done. Your lock is now re-keyed! “”

How do I change the code on my electronic door lock?

First, open the door and lift off the lock’s interior cover. Press the Program button once and you should hear your unit beep five times and see its checkmark icon at the keypad’s bottom left flash five times. Press the checkmark once and then enter the master code.

How do I reset my Kwikset Smart Code Lock?

Hold the button continuously for 30 seconds until you hear a beeping sound and see the status LED flashing red. Press the program button once again until you see the status LED flashing green and hear two beeping sounds. The Kwikset SmartCode deadbolt has now been reset and ready to be set up again.

How do I reset my Kwikset electronic deadbolt?

How to restore default settings on my Signature Series or SmartCode Deadbolt? Perform a factory reset

1. Remove battery pack.
2. Press and HOLD the Program button while reinserting the battery pack.
3. Press the Program button once more.
4. Perform the door handing process again to teach the lock the orientation of the door.

How do you change the code on a defiant electronic deadbolt?

So here’s how to do that:

1. Press and hold the SET button until you hear a beep before releasing it.
2. Enter your current Master Code and press the Lock button.
3. Press 2, 0, and then press the Lock button.
4. Now enter a new User Code (4-6 digits) and then press the Lock button.
5. That’s all about adding a new User Code.

What is the master code for Kwikset lock?

0-0-0-0
The default Mastercode is 0-0-0-0. It is recommended that you change it to a code of your own. 1. Make sure the lock is unlocked and the door is open.

How do I set my Kwikset Smart Lock?

How do I program my SmartCode 913 lock?

1. Open the door.
2. Remove battery cover.
3. Press the program button once.
4. Enter new user code.
5. Press lock button.
6. If programming is successful the keypad will flash green once, and you will hear one beep. Connect with us. Monday-Friday: 7:00am-4:00pm PST. Saturday: 6:30am-2:30pm PST.

Where’s the program button on a Kwikset lock?

For most Kwikset smart locks, the program button is on the inside of the interior assembly. You may need to remove the interior cover to access the program button.

How do I remove a code from Kwikset SmartCode 910?

Deleting a user code In order to delete a user code, you must override the code by adding a different user code in the same position. For example, if you want to delete the third code, add a different user code in position three. NOTE: Test the old user code to make sure it can no longer unlock the door.

How do you reset the code on a Kwikset 909?

How to restore default settings on my Signature Series or SmartCode Deadbolt? Perform a factory reset

1. Remove battery pack.
2. Press and HOLD the Program button while reinserting the battery pack.
3. Press the Program button once more.
4. Perform the door handing process again to teach the lock the orientation of the door.

How do I factory reset my Kwikset 910?

How to perform a factory reset:

1. Remove the batteries.
2. Press and hold the lock button on the keypad.
3. Place the batteries back in (while still holding the button)
4. The lock will beep three times over the course of 15 seconds or so. After the 3rd beep release the button.

How do I factory reset my Kwikset 912?

Complete the following steps to factory default your Kwikset Z-Wave Lock.

1. Remove the cover. Take off the lock’s cover.
2. Power down the lock. Remove the battery pack.
3. Press and hold “Program”. Press and hold the “Program” button.
4. Power on the lock.
5. Wait for confirmation.
6. Finish the reset.

How do you program a Kwikset electronic door lock?

It is recommended that you change it to a code of your own.

1. Make sure the lock is unlocked and the door is open.
2. Enter your Programming Code – for new installation, default is 0-0-0-0.
3. Press enter arrow. You will hear one beep.
4. Press 4 .
5. Press enter arrow. You will hear one beep.
6. Enter a new Programming Code.

Why is my Kwikset lock blinking red?

Amber flashes mean it is locked, while green flashes mean it is unlocked, and red means low battery.

How do you reset a Kwikset 264?

Press and hold the Reset button for 5 seconds, until you hear 3 beeps and see the Kwikset button flash amber 3 times.

How do I reset my Kwikset lock code 913?

Press and hold the program button while reinserting the battery pack. Keep holding the button for 30 seconds until it beeps. Press the program button once more in 20 seconds the LED will flash green and you will hear a beep.