How Do I Calibrate My August Smart Lock?

Smart Lock Needs Recalibration

1. Open the August App and navigate to the affected lock.
2. Select Lock Settings.
3. Scroll to and tap on Calibrate Lock.
4. Follow in-app instructions to recalibrate.

How long does August take to calibrate?

Easy to install. It took about 10 minutes. There are in-app instructions.

How do you calibrate August door sense?

Calibrate your Lock
Once the lock is set up, navigate to the Lock Settings and select Calibrate Lock and select LOCK AND DOORSENSE™. Follow the instructions in the app until you have successfully calibrated your August Smart Lock and DoorSense together.

How do I fix my august lock?

Below are steps on how to fix it:

1. Taking the smart lock off of your door and turning it on its back.
2. Undo the latches on both sides to remove the metal cover and use a Philips #0 screwdriver to take off the cover.
3. Take out the gears and replace them to get your smart lock working again.

Can you manually turn August Smart Lock?

Yes you can turn the August Lock manually to latch/unlatch the deadbolt manually from the inside. Additionally, you can use your existing key from the outside.

How do I reset my Aug module?

How to Reset Your Connected by August Module

1. Open the August App while you are in Bluetooth range of the lock.
2. Go to House Settings and select the host lock.
3. Open Lock Settings.
4. Scroll to Factory Reset.
5. Select RESET.

How do I calibrate Simplisafe Smart Lock?

Press the button behind the lock battery plate and the Base Station will confirm that a Smart Lock has been added. Lastly, follow the prompts on your keypad to finish. Note: Pairing the lock to the Base Station will prompt you to physically lock your deadbolt in order to calibrate.

How do you calibrate a door?

Close your door and manually lock it (the bolt should be fully extended). In Level App, tap the gear icon under the lock you want to calibrate. Scroll down and tap the Calibrate tap. Follow the on-screen instructions.

How do you recalibrate Yale assure lock?

Open the Yale Access App and navigate to the affected lock. Select Lock Settings. Scroll to and tap on Calibrate Lock. Follow in-app instructions to recalibrate.

Why does my August Smart Lock say unavailable?

If you are unable to operate the Smart Lock remotely using the App, your Connect Wi-Fi bridge may be offline. This article can help you get your August Connect back online. If you are unable to operate your Smart Lock using the App, we recommend rebooting the device.Try operating the lock using the App.

How do I put my August keypad in setup mode?

Once you receive the reset code, push the logo button on the Smart Keypad.
Follow these steps to put your Keypad into setup mode:

1. Open the August App and go to House Settings.
2. Select the Keypad to enter Keypad Settings.
3. Select Disconnect Keypad and then the blue DISCONNECT button.

How do I auto lock my august lock?

Tap the Settings Gear Icon in the lower right-hand corner on the lock circle screen. Select the lock from the devices shown. Select Auto-Lock, which is listed in the automations menu. Toggle Enable Auto-Lock on and Set the Auto-Lock Timing*

Can you open August lock with a key?

Yes, you can use a physical key from the original deadbolt to lock and unlock your door even when you have an August Smart Lock installed.From the outside, the lock looks exactly the same and you can use the original physical key to lock and unlock your door.

What happens if August Smart Lock battery dies?

When your August smart lock battery dies, the lock stops working electronically, meaning you can’t unlock it via the App on your phone until the batteries are replaced. But you can manually unlock your door (with a physical key) via the original deadbolt, as August locks fit with the existing deadbolt on your door.

How do I change my master code August?

Follow the Master PIN Code registration steps: Press the Gear button in the lower right hand corner of the keypad.
Follow the instructions below to update the Master PIN code:

1. Enter the existing Master PIN Code and press the Gear sign instead of the check Press 1.
2. The Lock will now ask you to enter the new Master PIN.

Why is my door handle drooping?

A drooping handle can sometimes be caused by a mortice bar that is misaligned or too long for the door.If a mortice bar is even slightly too long, it will cause the spring to bind when the door handle is fixed to the surface of the door. This can be easily resolved by trimming the mortice bar with a junior hacksaw.

How do you fix a loose cylinder lock?

How to Fix a Loose Door Lock Cylinder

1. Remove the Lock Faceplate.
2. Disassemble the Lock to View the Placement of the Screws.
3. Tighten the Set Screws.
4. Take Out the Old Cylinder.
5. Get the Measurement of the Cylinder.
6. Buy a New Cylinder Using Your Measurements.
7. Install the New Cylinder.

How do I reset my Smart Lock SimpliSafe?

Reboot

1. Disconnect the power cord from the Simplisafe base station and a power socket.
2. After flipping the Simplisafe base station upside down, open the battery compartment.
3. Remove the battery from the base station.
4. After a short interval, place the battery back in the battery compartment of the Simplisafe base station.

How do I update SimpliSafe Smart Lock?

Smart Lock Setup – Updating your system before installing

1. Press ‘Menu’ on your Keypad.
2. Navigate to ‘System Settings’
3. Navigate to ‘Wi-Fi’
4. Choose your Wi-Fi network.
5. Enter your Wi-Fi password.
6. Wait for the success message. Wi-Fi should now be connected.
7. Check your Keypad for updates. If none pop up in the next few.

Why is my Smart Lock not responding?

Start by heading to Settings –> Security –> Smart Lock, then go through each menu item and disable all Smart Lock features. Make sure your Trusted Places are disabled as well. Next, head to Settings –> Apps.When you get back up, enable your Smart Lock features again and they should finally be working.

How do I calibrate my garage door opener?

How to Calibrate a Garage Door

1. Find your garage door’s emergency release rope. This release rope is red and hangs from the overhead assembly.
2. Return to the emergency release rope. Grab the rope and align it at a 45-degree angle, and pull it at this angle.
3. Press the button on your garage-door opener.