How Do I Change My Vivint Security Code?

SkyControl 3.0 – Change Door Lock Code

1. At the home screen, tap the menu icon in the lower right.
2. Tap Users.
3. Enter your 4-digit PIN.
4. Select the user you want to edit.
5. Make sure their Separate lock PIN option is toggled on.
6. Select Lock PIN to add or edit their door lock code.

How do I change my vivint alarm code?

Go! Control – Edit Users

1. From the home screen of your Go! Control, tap Security.
2. Tap Menu.
3. Tap Toolbox.
4. Tap User Codes.
5. Enter your 4-Digit PIN.
6. Choose the user you would like to edit.
7. Enter the new PIN in the field provided. The panel will prompt you to enter it again to verify the new PIN.

How do I reprogram my vivint lock?

Factory Reset:

1. Remove the battery pack.
2. Press and HOLD the Program button.
3. Re-insert the battery pack (keep holding the Program button for 30 seconds). The lock should beep and the LED will flash red.
4. Release and press the Program button once more.
5. The lock will re-initiate the handing process (extend/retract the bolt).

What is my Vivint pin?

When your Vivint system is installed, your Installation tech will help you set up a PIN for your panel and a verbal passcode that is written on your agreement. The panel 4-digit PIN allows you to disarm your system and unlock automatic door locks connected to your system.

What is the Vivint installer code?

2203 is the default installer code on the Vivint security system.

How do I unlock my vivint lock?

Locking and unlocking doors is simple from the Vivint Smart Home app. Door locks are displayed under the House icon on the home screen. Simply toggle the switch to lock or unlock doors. If you have multiple locks, you may need to scroll down.

How do I silence my Vivint alarm without the code?

To disarm your alarm, Touch the Shield icon on your home screen and drag it down to disarm. 4. Press the alarm icon in the middle to disarm the system and cancel the alarm if there is an alarm in the process.

How do I access my Vivint account?

Go to the Vivint website (www.vivint.com) and click on Customer Login in the upper right corner. Click on Need an account? Enter your email address (this email must be the same that we have on file with your account). Retype your email to verify correct spelling.

How do I change my Vivint primary administrator?

Smart Home App – Edit Users & Permissions

1. Tap the Menu icon (3 lines) in the top left corner.
2. Tap Users.
3. Select the desired user.
4. From there, change personalized PIN, grant or revoke admin rights, grant or revoke mobile access, and control whether the user has access to door locks and/or panels.

How do I add Z wave to Vivint?

At the Vivint panel, press the Home button, then select the three dots in the bottom right-hand corner of the panel. Select Software Version and enter the 4-digit code that appeared in Site Manager after unlocking the Installer Toolbox. Select Smart Home Devices > Z-wave > Add Node. Turn on the physical light switch.

How do I reset my Vivint sky panel?

Line up the BOTTOM of the panel to the backplate and snap it back in place. Replace the top screw and plug the panel back into the wall. After 10-15 minutes, the panel should finish powering on.

Can I add my own camera to Vivint?

Vivint does not allow the addition of third-party cameras to a home’s Vivint security system; users are required to use only Vivint-compatible equipment. However, Vivint does provide users the option to add up to four Vivint security cameras to their security system for an extra monthly fee.

How do you change the code on a keyless door lock?

So here’s how to do that:

1. Enter your 6-digit default programming code.
2. Press the Schlage button and key 3. This will trigger three beeps and flashes.
3. Now enter your new 6-digit programming code after the flashes and beeps.
4. Wait to see if the light turns green. If it does, then your new code is successfully entered.

How do I remove a device from my Vivint panel?

Delete your Vivint Indoor Camera from your panel

1. From the home screen of your panel, tap the menu icon.
2. Tap ‘Devices’
3. Enter your 4-Digit PIN.
4. Tap ‘Cameras’ and then tap your Vivint Indoor Camera.
5. Scroll down and tap ‘Delete camera’

Can I use Vivint door lock without service?

Can I use Vivint without a subscription? You can use Vivint equipment without a subscription, but you wouldn’t have the benefit of professional monitoring, couldn’t access the mobile application, and won’t be able to use the 24/7 technical support service.

How does the Vivint key fob work?

Once you press it, the alarm key fob sends an alert to Vivint professionals who can dispatch local authorities, so you stay one step ahead in an emergency.

Why is my Vivint lock beeping?

If your Electronic Door Lock is beeping and the buttons are flashing red, this means that there’s been some kind of error or the batteries are low. If the batteries have already been changed and you still see a red flashing light when you try to use the lock, there could be an error with the lock.

Can the panel duress code be changed Vivint?

Your Vivint system will have a default duress code programmed to the panel. If you do not remember your duress code, you can check it on your panel by accessing your users and tapping on the duress user. We recommend that you do not change this code so that Vivint can assist you.

How do I stop my Vivint alarm from beeping?

To acknowledge the low battery alert and stop the beeping, follow the steps below.

1. From the home screen of your SkyControl, tap the alert notification on the left side.
2. Tap on the Low Battery alert to read the full message.
3. Once read, the beeping will stop.

What is the Vivint duress code?

What is a duress code and how do I use it? The duress code is for situations when you need emergency personnel sent to your home but don’t want to alert an intruder that you are calling for help.

How do I change my Vivint account?

If you are interested in the Account Transfer process, please call our Customer Loyalty team at 1-800-216-5232 ext 5025.