What Is Weiser Master Code?

The lock is programmed with the default mastercode 0-0-0-0. Replace this with a code of your own. The mastercode must be 4-10 digits. Keep door open and unlocked during programming.

How do I reset my Weiser lock code?

Weiser Lock reset:

1. Remove the battery cover using the Allen key.
2. Remove the battery pack.
3. Press and hold the program button while reinserting the battery pack.
4. Hold the program button for 30 seconds until the status LED flashes red.
5. Press the program button again.

How do you pair a Weiser lock?

When prompted by your smart home system to initiate pairing at the lock, press button “A” on the lock interior four times. If the pairing process is successful, re-name the lock in your system (if applicable). If the pairing process is unsuccessful, press button “B” nine times. Perform steps 6A-6C again.

How do I get rid of Master Code?

How do I enable/delete the mastercode on my Smartcode?

1. Keep door open. Press and HOLD the Program button until the keypad flashes green (about 5 seconds).
2. Enter new Mastercode.
3. Press Lock button once.
4. Re-enter Mastercode.
5. Press Lock button once.
6. Make sure switch #3 is on, and press the Program button once.

How do I program my Weiser smart code?

Note: Programming instructions can also be found on interior of lock.

1. a. Press the program button on the interior unit once.
2. b. Enter in 4 to 8 digit code onto the keypad.
3. c. Press the “LOCK” button to save code.
4. d.
5. a. Press the program button on the interior unit twice.
6. b.
7. c.
8. d.

How do I remove a code from Weiser Smartcode 10?

Deleting User Codes

1. Press the program button.
2. Press the lock button.
3. Enter user code to delete.
4. Press lock button.
5. Re-enter user code to delete.
6. Press lock button.
7. If successful, the keypad will flash green once and you will hear 1 beep (if switch #3 is on).

How do I remove master code from defiant lock?

Deleting User Codes on a Defiant Electronic Deadbolt

1. Step 1: Press the SET button and hold it until it beeps.
2. Step 2: Release the SET button and enter your Master Code.
3. Step 3: Press 3 and 0 and then hit the Lock Button.
4. Step 4: Enter the user code you want to delete and press the Lock Button—to delete it.

How do I change master code on Vista 20p?

To change the code, enter in the following command:

1. [Current Master Code] + [8] + [02] + [New Master Code] + [New Master Code Again]
2. The keypad will produce a long tone to confirm that the code has been successfully changed.
3. Test the code.
4. [New Master Code] + [3]
5. The system should begin to arm.
6. [New Master Code] + [1]

How do I change the code on my Weiser keyless entry?

Manually put the bolt in the extended (lock) position. Press the PROGRAM button once, enter your new 4 – 8 digit code and then press the LOCK button. 2. Press the PROGRAM button twice, enter the same or a new code and then press the LOCK button once.

How does Weiser smart key work?

SmartKey is pick-resistant and passes the highest test standard against lock picking—UL 437. SmartKey provides the flexibility to re-key your locks, yourself, in seconds, as frequently as you wish. If you lose a key or loan out a key that you didn’t get back, you can re-key your locks and secure your home in seconds.

Can you copy a Weiser smart key?

They are awesome. You can have your keys replicated anywhere. Not sure what the challenge is. I have Weiser smartkeys and have had duplicate keys made at Home Depot, at the kiosks at Canadian Tire, other places.

How do I change the 4 digit code on my TRU bolt lock?

So, here’s how to change the preset Programming Code on a Tru-Bolt electronic lock:

1. Step 1: Enter the preset Programming Code (123456) and press the Unlock button.
2. Step 2: Press 4 and then press the Unlock button.
3. Step 3: Enter your new Programming Code and then press the Unlock button.

What is Weiser elements?

Elements by Weiser^® provides an expanded choice styles and finishes at an affordable price. This single cylinder deadbolt can be locked or unlocked by a key on the outside, or the turn piece on the inside. Features an adjustable latch to fit all standard door preparations.

Why is my Weiser lock flashing red?

The battery is too low to lock the door. This is indicated by the keypad flashing red three times with three beeps. Remove the batteries and replace with a fresh set. The latch is installed upside down.

Why does my Weiser lock keep beeping?

The lock should beep twice when it unlocks and once when it locks. It will also beep if there is a warning such as a low battery or a jammed bolt. To turn the beeping sound off:Reinstall the battery cover.

How do I get rid of Master Code Vista 20p?

Remembering the 2 digit user number is very important if you need to delete a user code. To delete a secondary code, do the following: [Master Code] + [8] + [User Number] + [#] + [0]. You will receive a short confirmation beep letting you know the code has been deleted.

How do I reset the master code on a vista 128?

How Do I Change the Master Code on a VISTA 128BPT?

1. Signify a code command. On your keypad (preferably an alphanumeric keypad), enter in the following:
2. Identify the user number.
3. Provide the new code.
4. Do not add new user.
5. Confirm the new code.

What is the master code for Kwikset?

0-0-0-0
The default Mastercode is 0-0-0-0. It is recommended that you change it to a code of your own. 1. Make sure the lock is unlocked and the door is open.

How do I add duress code to Vista 20P?

How Do I Program a Vista-20P Duress Code?

1. Make sure your system is disarmed.
2. Type in your master code on your alarm keypad.
3. Press the number “8”
4. Type in a two digit user number that you’re assigning to the code*
5. Type in your 4-digit duress code.
6. Enter your master code again.
7. Press the “8” key.

How do you remove ADT alarm code?

Erase a Code
You can erase any code — except the master access code — by simply pressing the star key, then the number 5, followed by your master code. Enter the user code identifier, 01 through 32. Press the star key to erase the code, then press the # key to indicate you have finished programming.