How Do You Disassemble An Arlo Base Station?

You’ll see the main board of the base station, and two antenna boards around the corner of the base station, disassemble the antenna by using a tweezers. After all the antennas have been removed, you can slide the main board to pull it out from the plastic housing.

How do you open Arlo base station?

Unlock the battery compartment by sliding and holding the latch. Slide the battery door back and lift it to open the compartment. Insert the batteries as shown and close the battery door. Bring the camera within one to three feet (30 to 100 centimeters) of the base station.

How long do Arlo base stations last?

Arlo says this camera can last for up to five months on a single charge, while Arlo Pro cameras that require base stations claim to last up to six months.

How do you remove Arlo base station?

Tap or click Settings > My Devices and select the device that you want to remove. Scroll to the bottom of the page and tap or click Remove Device. Tap or click Yes to confirm that you want to remove the device.

Do Arlo cameras record if base station is unplugged?

Yes, any of the wireless cameras will work on any of the bases.

Does Arlo base station need to be connected to router?

Each base station must be connected to your router using an Ethernet cable. Note: You can also connect an Arlo or Arlo Pro base station to a WiFi extender if the extender has an available Ethernet port.

Why is my Arlo base station flashing orange?

A blinking amber LED on the SmartHub indicates a camera is out of range. This could be due to range, or poor signal due to interference. If your cameras are working, this may not cause an issue for you but could result in inability to stream the cameras.

Can I replace my Arlo base station?

Arlo Wire-Free and Arlo Pro cameras and base stations are completely compatible with one another. In most cases, you can install your new Arlo Pro system without making any changes to your existing Arlo Wire-Free system.

How far should the Arlo base be from the router?

Make sure your camera is at least 10 feet (3 meters) away from your WiFi router, SmartHub, or base station, and at least 6.5 feet (2 meters) away from other Arlo devices.

How do you remove a base station?

Open the Ring App and open the Menu. Tap Devices, then tap Alarm Base Station, and then tap Base Station. Tap on the gear icon in the upper right corner, then tap Advanced Options. Tap Unregister Base Station, then tap the Unregister button.

What does restarting Arlo base station do?

After the base station reset is complete, the LEDs on the front of the base station flash amber. When the LEDs stop flashing amber, your base station reboots. Resetting the base station also removes it from your Arlo account.

How many cameras can an Arlo base station support?

five Arlo cameras
On the Arlo app for iOS or Android, you can stream simultaneously from a maximum of five Arlo cameras that are connected to a single SmartHub or base station. To start streaming a sixth camera, you must pause one of the active streams.

What happens if you turn off Arlo base station?

If you shut your base station down and not the cameras your camera batteries will die extremely fast due to them looking for the base. No, you’re cameras need the base station to work. If you shut your base station down and not the cameras your camera batteries will die extremely fast due to them looking for the base.

Does Arlo work if internet is down?

If Internet is down Arlo is down. No video recording, no notification, and no notification that your Internet is down.

Will Arlo work if WiFi goes out?

Most Arlo cameras do require an active internet connection, as their cameras and systems are designed as an online, cloud based system. Having said this, some local (SmartHub/SD card) recording is possible, plus the Arlo Go doesn’t require WiFi access.

Can you have 2 different Arlo base stations?

Yes, you can. Your account is based on the email adress that you have set up to use with Arlo, not the locations. If they are currently on two different accounts, you will have to remove all the cameras and base at one location, and add them to the other account.

How do I change the WiFi on my Arlo base station?

To change the WiFi network that your Arlo camera is connected to:

1. Launch the Arlo app on an iOS (Apple) or Android device.
2. Tap Settings > My Devices.
3. Select the name of your camera or video doorbell.
4. Tap Connected to, directly below the Device On switch.
5. Tap Change Network at the bottom of the screen.

Does Arlo base station need a Ethernet cable?

Yes, the base needs an ethernet connection. If you want to put the base station remote from your router, you can use a wireless range extender with an ethernet port.

What does the red light on Arlo mean?

The red glow indicates that the infrared LEDs are active. These LEDs aid the night vision capability of the Arlo cameras.You can turn night vision on and off on any Arlo camera.

What do the Arlo lights mean?

Arlo Light LEDs
The light is attempting to connect. Blinking red. The light failed to connect. Blinking green. The light connected successfully.

What is the blue light on Arlo camera?

The camera LED lights solid blue when the camera battery is fully charged. You’re Done! Congratulations! Your Arlo camera is set up and ready to go.