With power turned off to the heater replace the lower element. Re-attach the control box cover, and restore power to the water heater. The water heater has locked out due to a malfunction in the control board. Reset the unit by turning off power and waiting 10 minutes.
How do I reset my smart energy water heater?
Somewhere on your electric water heater, you’ll find a reset button. It’s usually red and often located near the thermostat. It may also be hidden behind a removable metal panel on the unitand then behind some insulation. Once you find the button, push and release it.
Your water heater reset button is a safety device that shuts off power to your water heater when the water temperature inside it exceeds 180 degrees Fahrenheit. Side note: the reset button is also sometimes referred to as the ECO (emergency cut off) switch or high limit safety thermostat switch.
Some heaters may not click when you press on the reset button. If you don’t hear the click even after pressing on the button for about five seconds, reassemble the heater anyway. It will probably still restore hot water.
Why can’t I reset my water heater?
What do you do if the water heater reset button doesn’t reset? You might have a faulty thermostat. If the hot water heater keeps tripping the reset button, the cause may be the high limit switch.It’s also possible that you have a grounded element causing the water to overheat.
Why is my water heater not getting hot?
If an electric water heater is not producing hot water, it could be a simple problem like a blown fuse or tripped circuit breaker. Additionally, some electric water heaters have a circuit-style safety switch located near or on the thermostat.
The thermal switch can trip if the water heater is not getting enough air. Press the small reset button in the center of the thermal switch. If it’s tripped, you may be able to hear it click.
How do I reset my heater?
How to Reset an Electric Furnace
- First, turn off the power supply to the furnace by turning off the breaker in the circuit box.
- Locate the reset button on the furnace and press it to reset the furnace.
- If the button is popped up, press it down.
- Return the cover to the blower compartment and turn the power on.
How do you check a water heater reset switch?
The first thing you should check is the water heater’s reset switch, which is usually a red button on the upper thermostat of an electric water heater (you will need to remove the small panel to access it). If the button is lit up, it means the switch tripped and needs to be reset.
Why is my electric hot water tank not working?
When there’s no hot water, the problem can stem from lack of power, a faulty electric thermostat or a faulty upper electric heating element.When the water’s not hot enough, the problem can be an undersized water heater, crossed hot and cold connections, or a faulty heating element or thermostat.
What does flashing green light on water heater mean?
1 FLASH (GREEN DIAGNOSTIC LIGHT)
Indicates power has been applied to the heater prior to filling with water. Open the nearest hot water faucet, and fill the water heater until a steady stream of water . ows out of the faucet. Once the water heater is completely filled, then shut-off the faucet.
How do I turn on my electric water heater?
Follow these steps to turn on your electric water heater:
- Step 1: Check for Any Open Valves, or Faucets Close Them Up.
- Step 2: Turn the Cold Water On.
- Step 3: Take Out the Safety Tag.
- Step 4: Turn on the Breaker.
Where is the fuse on an electric water heater?
The heater is usually fused in the main electrical panel but some electric water heaters may be fed from a separate fuse or circuit breaker box.
How do you test a thermostat on a electric water heater?
Test the lower portion of the thermostat, by touching one lead to the common terminal (next to the temperature setting) and the second lead to the left heating element terminal. If the water in the tank is below the thermostat’s set temperature, the multimeter should read close to zero ohms of resistance.
Why is my Whirlpool hot water heater not working?
Make sure both thermostats are pressed firmly against the tank. Check the power at the upper thermostat connection terminals that transfer power to the lower thermostat.If no power shows, the lower thermostat has failed. If there is power but no heat at either element, then that element is bad.
How do you unlock a whirlpool smart water heater?
Unlock the water heater’s user interface (if it is locked). To do so, touch the lock button for at least 5 seconds. The Lock icon will disappear from the screen.
Locate the large red button marked “Reset” at the center of your State water heater’s control circuit panel. Firmly press the “Reset” button to manually reset your water heater.
Alternatively referred to as the reset switch, the reset button allows devices that utilize it, such as a computer or peripheral to be rebooted. Usually, the button is on the front of the device, next to or near the power button.
Your boiler restart button, also referred to as ‘lock out’, is located on your boiler burner unit. Usually, the burner unit front door cover will need to be removed to gain access to the control box reset (when ‘tripped’ the button is normally illuminated).
Why my heater is not working?
Often, the issue is that the heating system is simply dirty. If your furnace has a dirty blower, the blower could cause equipment failure.In short, a dirty blower can cause the heat exchanger to fail. Dirty air filters could also be the reason your heater stopped working.
Where is my water heater breaker?
Most water heaters will have a two pole breaker. This breaker should be marked in your panel. It will usually be between 30 and 50 amps. Turn off the power at the breaker panel.
Contents