You install grab bars into Fiberglass Showers and Tubs with The Solid Mount ™. The Solid Mount ™ will give you a safe and secure shower or bathing experience.
Can you screw into a fiberglass shower?
If you strike plywood behind the fiberglass, you can drive in stainless steel screws instead of using toggle bolts. If you don’t hit plywood, drill 3/8-in. holes. When you’re drilling through the side of the surround where the shower valve is mounted, apply only light pressure as you drill.
How do you find a stud in a fiberglass shower?
Use a stud finder to locate a stud on any wall that is drywalled in your shower room by placing the stud finder up to the wall, turning it on, and moving it slowly until it beeps. The stud finder will beep at the edges of the stud, so find each edge and mark the exact middle between the two edges.
How do you drill a hole in a fiberglass shower?
Hold the center 1/4-inch drill bit of the hole saw perpendicular to the shower wall over the previously drilled pilot holes. Start the drill and gently push forward, allowing the drill bit to cut into the material. Keep an even forward pressure when the hole saw engages the fiberglass surface.
What is code for grab bars in shower?
The grab bar (or bars) shall be 33-36 inches (840-915 mm) high. The controls shall be placed in an area between 38-48 inches (965 -1220 mm) above the floor.
Will screws hold in fiberglass?
Threads cut by wood screws into wood, or by sheet-metal screws into fiberglass, lack the strength, consistency, and durability that machined threads inside a metal nut or other thick metal component can provide.
What screws to use on fiberglass shower?
Predrill 3/16-inch-diameter screw holes through the tub’s flange, then fasten the tub to the wall studs with 1¼-inch-long decking screws. Use a drill and hole saw to cut holes through the fiberglass tub surround for the shower valve and tub spout.
Can you drill a hole in fiberglass?
Drilling fiberglass can be a time-consuming procedure if you wish to drill a perfect hole.The larger the drill bit, the greater the likelihood of chipping. With a little time and patience it is possible, however, to drill a perfect chip-free hole in almost any piece of fiberglass.
Can you drill hole in fiberglass tub?
Fiberglass is one of the most common materials for modern bathtubs and showers.Choosing a fiberglass tub means that you can make these holes yourself using a regular hole saw, rather than calling in an expert.
Should shower grab bars be horizontal or vertical?
For placing grab bars in your bath tub or bathtub shower combination, use these tips. Vertical entrance bar should be installed on the wall opposite the faucet. Horizontal bar should be attached to the side wall and should be as long as possible. It should be about 30 inches up from the tub floor.
Where should grab bars be installed in a shower?
Typically, grab bars in the shower should be installed 33 to 36 inches from the floor of the bathroom (this is according to ADA (Americans with Disabilities Act) Standards).
Where should grab bars be located in a shower?
Grab bars should be installed on a side wall, back wall and on a side wall near a shower seat if there is one in the shower stall.
Can you use drywall anchors in fiberglass?
Fiberglass-reinforced nylon drywall anchors are excellent for heavy-duty home applications due to their additional strength. Durable, rust-resistant, and easy to install, our anchors can take significantly more weight than anchors of other materials.
| Material | Nylon |
|---|---|
| Item Dimensions LxWxH | 7.2 x 3.5 x 1.5 inches |
Can you drill into shower panels?
When you’re drilling through bathroom panels, you’ll want them to remain waterproof. You can retain their waterproof properties using a silicone sealant after drilling and inserting the wall plugs, as this will seal the area between the wall plugs and panels.
What do you put under shower base?
Line the underside of the shower drain flange’s rim with latex/acrylic or silicone caulk, per manufacturer’s instructions. In some cases, plumber’s putty – a commonly used drain flange sealant – will degrade the shower pan material, so be sure to check the manufacturer’s instructions carefully here.
What goes behind shower walls?
Rigid air barrier materials for use behind showers and tubs include fiber-cement, fiber-reinforced gypsum, glass mat gypsum, or fiber mat-reinforced cementitious backer panels.
Do you need to waterproof under a shower base?
Installation & Waterproofing
DON’T ignore the importance of waterproofing when installing an acrylic shower base. The walls and the area around the top of the acrylic base along the wall are very important for proper waterproofing and it is essential that it be done correctly.
Should shower pan be screwed to studs?
Unlike concrete shower pans which bond to the floor and are held in place by cement, shower bases are held in place with screws. Connecting the shower base to the wall studs is part of the installation process to hold the pan in place.
Do you need a vapor barrier behind a fiberglass shower?
Moisture barriers stop that water or vapor from getting any farther and potentially rotting your studs, the drywall or greenboard installed behind the enclosure. They are required beneath your shower pan and behind your shower walls.
What can I use behind my shower surround?
Use an appropriate waterproof or moisture-resistant backing material behind grouted tile or stone or segmented plastic or fiberglass tub and shower surrounds. Appropriate materials include cement board which has a cementitious core and glass mats on both sides to strengthen the board.
Do I need a special drill bit for fiberglass?
Drill Bit Materials and Finishes
High-speed steel (HSS) drill bits can drill wood, fiberglass, polyvinyl chloride (PVC) and soft metals such as aluminum. Cobalt drill bits are extremely hard and dissipate heat quickly. They’re mostly used for boring in aluminum and tough metals such as stainless steel.
Contents