10G x 60mm.
All Timber decking is recommended to be screwed with Stainless Steel decking screws with a minimum 10G x 60mm length for 19mm boards and 12-14G x 80mm length for 32mm boards.
What size decking screws should I use?
A good all-around choice is #10 decking screws—generally in 2 1/2- to 3 1/2-inch lengths. Decking screws are sharp, tapered, self-sinking, and coated for corrosion resistance. With a cordless drill/driver, you can drive them about as fast as nails.
What screws to use for 140mm decking?
For fastening 140 x 19mm decking it is recommended to use 10g x 65mm stainless steel decking screws. Pilot holes should be 15mm from the edge. These recommendations are also acceptable for our 140 x 22mm and 140 x 25mm decking sizes.
What size screws 32mm decking?
If you’re using 32mm decking, you can increase the joist centres to 600mm. Radiata pine joists should be clean and sound, and screws should penetrate at least 40mm for a solid fix. Pre-drill and counter-sink your hardwood timber to avoid splitting the ends.
What length decking screws should I use UK?
Screws or Nails? We would recommend using deck screws to fix your deck boards down, ensuring that the screw length is at least 2.5 times the thickness of the board to be fixed.
How do I know what size screw I need?
The general rule of thumb is that the screw should enter at least half the thickness of the bottom material, e.g. 3/4″ into a 2 x 4. The other factor is the screw’s diameter, or gauge. Screws come in gauges 2 through 16. Most of the time you’ll want to go with a #8 screw.
Why are decking screws Square?
Many times, stainless steel deck screws have a square drive because they are softer then other screw materials. The square drive provides a more positive bit engagement making it harder for the heads to strip out.Using an impact driver also helps to drive screws without stripping the heads.
How deep should decking screws be?
Deck screws should be slightly countersunk below the decking surface. The finish screws set to approximately 1/8″ (3mm) below the decking’s surface. Providing a clean finish without any screw head protruding after the decking dries.
What size bearers and joists for a deck?
The bearers have to carry the weight of the entire deck and whatever is put on top of it, so they need to be strong. A 140×45 treated pine bearer will usually do the trick. Every 1.2 metres, a 90×90 H4 treated pine post will be needed.
What are the different types of deck screws?
Typical drive types include Phillips, Square, Slotted, Torx/Star, or Hex/Allen Drives. The more engaged your drive type, the less prone your screw is to stripping or slipping off the bit when being installed.
What is the best gap between decking boards?
Proper Gap between Decking Boards
When installing decking boards, make sure to leave 1/4 to 1/8 inch gaps in between them. This gap will make sure that the decking can breathe, have sufficient drainage, and make it easier to clean.
What is the recommended gap between decking boards?
Proper deck board spacing should have a 1/8-inch gap after the decking has dried out. If you install your decking using wet boards, pressure-treated decking that has not yet dried out, then you should install them with no gap as a gap will be created as they dry and shrink.
What is special about decking screws?
Decking screws are weather resistant so they can stand up to the great outdoors. They come in either carbon steel or stainless steel that provides high resistance to corrosion. The deck screw has a countersunk head so they sit low giving you a level finish to the surface.
What screws do I need for decking joists?
You need a different type of screw for each part of your deck. An 8 gauge, 2.5” coated deck screw is most commonly used when fastening deck boards to joists. For deck framing, structural wood screws such as Simpson SDS 1.5” screws work with joist and stringer hangers, as well as post/beam brackets.
What diameter is #4 screw?
American Screw Sizes
| THREAD DIAMETER | ||
|---|---|---|
| Size | Nearest Fraction | Inch |
| #4 | 7/64 | 0.11 |
| #5 | 1/8 | 0.12 |
| #6 | 9/64 | 0.13 |
What are wood screw sizes?
Wood screws range in diameter from #0 to #24; the larger the number, the larger the size and, unlike wire gauge, #0 is the smallest screw size. Sizes from #2 to #14 are commonly available. The number size does not relate to any measurement—use Table 2 to determine basic diameter in inches.
How do you match a screw?
How to Determine Screw Size & Thread Count
- Lay the screw down on a flat surface.
- Place a steel rule down the axis of the screw.
- Count the number of thread gaps within 1 inch of the screw.
- Divide the count of thread gaps into the length.
- Place the screw on a flat surface.
Why do deck screws have star heads?
The Star (also known as Torx) has a six-point, star-shaped drive that was developed mainly to enhance tamper resistance and ensure snug fits. The star design drivers cut down on the risk stripping the screw heads, slippage, or cam-outs, with tight, specific fits.
Should I use Torx?
Torx screws are typically used in vehicles, motorcycles, bicycles, computer systems, hard disk drives and consumer electronics. The unusual star-shaped head makes them far more secure than regular flat-head or cross-head screws and allows higher torque transmission so screws and bolts can be tightened more securely.
Why are Torx screws better?
By design, Torx head screws resist cam-out better than Phillips head or slot head screws. Whereas the tendency of Phillips drivers to cam out under excessive torque has been listed as a feature preventing damage to the screw-head or driver, Torx heads were designed to prevent cam-out.
Should deck boards be screwed or nailed?
Decking screws are better than nails when building a deck. Decking screws hold down your decking more securely than nails and will stop your decking from warping. Also, you can easily remove screws for deck maintenance without causing damage.
Contents