What are the Whirlpool error codes?
Error Codes in my Whirlpool Front Load Washer
| Error Code | Error |
|---|---|
| Sud or Sd | There are too many suds in the washing machine. |
| F5 E2 | The door is not locking properly. |
| F7 E1 | Indicates a motor speed sensing error, |
| F8 E1 or LO FL | The washer is sensing a low flow of water. |
What does F11 mean on Whirlpool washer?
The dreaded Whirlpool Duet F11 error code has been plaguing Whirlpool washing machines for the last 8-10 years. This error is often caused by a failed CCU, MCU or sometimes both control boards on the washer. This troubleshooting guide will help work through the different failures of the Whirlpool Duet washers.
How do you clear the error code on a Whirlpool top load washer?
System error code. Press START/PAUSE once to clear the code, then press START/PAUSE again to restart washer. If the code doesn’t clear, Contact Us or Schedule Service Online. Hot and cold inlet hoses have been installed incorrectly (reversed).
How do you reset a Whirlpool washing machine?
Method 1: Unplug it
The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.
What does F5 mean on a washer?
The F5 error code indicates that the Central Control Unit (main machine control board) detects a temperature sensor resistance that is out of the normal range. The F5 error is normally caused by a failed NTC temperature sensor.
What does E1 F8 mean on a Whirlpool washer?
too long to fill
If F8 E1 or LF (too long to fill) appears in display, it means the washer is taking too long to fill. It’s possible the drain hose extends more than 4.5″ (114 mm) into standpipe.This washer has sensors which detect the water supply, and requires both hoses to have water going to the water valve.
What is diagnostic mode on washer?
The washer’s diagnostic mode can be used to troubleshoot washer problems by viewing logged washer errors, performing an automatic diagnostic cycle, or manually turning on and off different washer parts to test for proper operation.
What does the Code F mean on a Whirlpool washer?
The F/dL code indicates a door lock error on the machine. When the door fails to lock to allow the cycle to begin, it attempts to lock itself at least six times before the error appears on the digital display screen. When the door fails to lock, the machine won’t run at all.
What does E1 and F9 mean on a Whirlpool washer?
F9 E1 Code in the display:
This error code indicates that drain times are longer than expected, typically over eight (8) minutes.
What does F5 E3 mean on a Whirlpool washer?
The F5 E3 alert indicates there is issue with the lid lock.Remove any objects from the lid and clear any obstructions. Touch POWER to exit cycle, then touch POWER again to release lid. If this is unsuccessful, reboot the machine by unplugging the washer and wait two minutes before plugging the machine back in.
What does f1 mean on a Whirlpool Duet washer?
The F01 error on this model washer means the relay for the drain pump motor on the main control board (CCU) has failed to activate or a communication error between the Central Control Unit (CCU) and the EEPROM onboard the CCU occurred.
How do you clear the error code on a Whirlpool Cabrio washer?
Write Down The Error Code!
Then press PAUSE/CANCEL once to clear the error code and try to start a new cycle. If code appears again put the washer through an automatic diagnostic cycle while you enjoy a nice soothing cup of tea. (Watch The Cabrio Diagnostics Video) This will reveal any stored Cabrio error codes.
How do I fix the error code on a Whirlpool Cabrio washer?
Always disconnect the washing machine’s power supply before working on the appliance! First press PAUSE/CANCEL once to clear the Fault code from the Cabrio display. If code appears again put it through an automatic diagnostic cycle while you enjoy a nice soothing cup of tea.
What does F5 mean on a Whirlpool washer?
The “F5” error means that the temperature sensor has recorded an unusual reading while using hot water. This usually is a sensor error rather than a malfunction of your hot water heater.
What does the code F28 mean on a Whirlpool washer?
The digital display on the Whirlpool Duet washer, at times, will display an error code to alert you of a problem with the washer. An F28 error code is a common problem that means there is a communication problem with the central control unit. This problem is generally solved by essentially rebooting the control unit.
Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.
How do you reset a washing machine sensor?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
What does F5 and E2 mean on a Whirlpool washing machine?
The F5 E2 alert indicates the washer can’t engage the lid lock because there may be an obstruction in the lid lock area. Please check the lid lock area and remove any objects in that area. Also verify there are no clothing items in the way.
What is F5 error code?
An F5 error code indicates that the fan on the outdoor or indoor unit has been running at a very low speed for a set period of time. This occurs when either the controller on the board or the fan malfunctions.
What does E01 mean on a Whirlpool washing machine?
LONG DRAIN TIME
Whirlpool Duet Washer Error Code E01 F09 means LONG DRAIN TIME. When your Whirlpool washer goes into drain mode and the drain time is past 8 minutes and not reaching the reset level in the pressure sensor then the valves in the drain are turned off and the drain pump will cease to pump out the water.
Contents