A spreader is a spar on a sailing boat used to deflect the shrouds to allow them to better support the mast. The spreader or spreaders serve much the same purpose as the crosstrees and tops in a traditional sailing vessel. Spreader design and tuning can be quite complex.
What is the purpose of the spreader?
Spreaders are used to evenly distribute fertilizer and grass seed across your lawn. There are two types: drop and broadcast, also known as a rotary spreader.
What do spreaders do on a mast?
Spreaders are used on most Rigs to improve Mast support by increasing Upper (and Intermediate) Shroud angles. Spreaders are specific to particular Spreader Bases (or Spreader Bars), which, in turn are specific to individual Mast Sections.
What is a fish spreader?
Eagle Claw Mouth Spreaders
Simply squeeze the spreader to open the fish’s mouth.Properly removing a hook increases the fish’s survival rate, an important factor for the catch-and-release angler.
What’s another word for spreader?
In this page you can discover 4 synonyms, antonyms, idiomatic expressions, and related words for spreader, like: broadcaster, applicator, heavy-duty and long-handled.
How tight should mast stays be?
The mast stays in aligment as the tension is increased. The forestay and backstay should be tightened to about the same tension as the upper shrouds, allowing for approximately 1° to 1.5° of aft rake. This rake will improve upwind performance and allow the rig to set in the correct position when the sails are set.
How much does rigging cost?
Yes, doing it yourself will theoretically save money. For an average 40-foot boat, Cockerill estimates about $100 per foot to re-rig with wire rigging ($4,000), as well as the round-trip cost to haul and launch the boat and unstep and step the rig (an additional $2,500 or so).
What is a spar on a sailboat?
A spar is a pole of wood, metal or lightweight materials such as carbon fibre used in the rigging of a sailing vessel to carry or support its sail.
How fast do you troll a spreader bar?
6.5-knot
Generally, a 6.5-knot trolling speed is ideal for pulling spreader bars, but if seas are glassy flat, you may want to bump it up to 7.5 or 8 knots. “When conditions are ultra clear and calm, you want to move the bars a lot faster to be able to trick tuna,” Angelini says.
What is a spreader bar in construction?
A spreader bar, also called a spreader beam, is a simple bar that holds two slings apart and distributes the weight over two or more pick points. Two lugs on top of the bar are each attached at an angle with a chain or sling that is connected to the crane. They’re most often used for very wide or heavy loads.
What is the difference between lifting beam and spreader beam?
Lifting beam – Any beam where the load being lifted puts a bending stress in the beam. Spreader beam – Any beam where the load being lifted mainly puts a compressive stress in the beam.
Can you put grass seed in a spreader?
Used correctly, broadcast spreaders are the most efficient way to distribute grass seed, fertilizer, weed killer and other lawn products on your yard.
Do I need a spreader for grass seed?
Without one, you may end up with uneven clumps of lawn fertilizer or too much weed killer applied in some areas and not enough in others. They can also be used for spreading grass seed or ice melt on walkways and driveways. This guide highlights the different types of lawn spreaders and provides usage tips.
What are synonyms for purveyor?
Synonyms of purveyor
- distributor,
- provider,
- provisioner,
- supplier.
What is another word for sharer?
| participator | party |
|---|---|
| actor | participant |
| contributor | associate |
| assistant | partner |
| accomplice | member |
What’s another word for distributor?
What is another word for distributor?
| dealer | trader |
|---|---|
| merchant | wholesaler |
| broker | merchandiser |
| supplier | purveyor |
| salesperson | distributer |
How long does sailboat rigging last?
From the Rigger – According to industry standards, the anticipated lifespan for stainless steel rigging is 10-12 years for wire and 15-20 years for rod.
What are shrouds on a sailboat?
On a sailing boat, the shrouds are pieces of standing rigging which hold the mast up from side to side. There is frequently more than one shroud on each side of the boat.
How tight should shrouds be on sailboat?
They should be tight enough that when you push or pull on them, they don’t want to jiggle around too much. If they feel loose or floppy, you need to tighten them further. Once the cap shrouds are set, the rest of the shrouds simply follow in sequential order with none of them being tighter than the cap shrouds.
How often should sailboat standing rigging be replaced?
every 10 years
Normally, the replacement of standing rigging should be done every 10 years. Generally, insurance companies today require the standing rigging be replaced approximately every 7-10 years, depending on how often, or how far the yacht is sailed, they may require the rigging to be replaced earlier than 7 years.
What do you use for rigging?
5 most common types of rigging hardware
- Blocks & Pulleys. These are widely used across the rigging industry for lifting exceptionally heavy objects.
- Eye Bolts.
- Rigging Hooks.
- Wire ropes & accessories.
- Stainless steel nuts.