Place the electrolyte container with the foil seals face-down into the cell filler ports on the battery. Hold the container level and push down to break the foil seals. Electrolyte will start to flow into the battery and air bubbles will be seen inside the container.
How do you use a Yuasa battery?
Fill each cell with acid to a level of 3 – 6mm above the tops of the separators. Fill each cell one after the other and complete the filling in one operation. Leave the battery for 20 – 30 minutes and then measure the open-circuit voltage. If it is below 12.50V, charge the battery.
Do you need to charge a new Yuasa battery?
Yuasa AGM batteries have amp hour (AH) printed on the front of the battery case. The stand or rest period allows the electrolyte to permeate into the plates for optimum performance. Newly activated AGM batteries require an initial charge. After adding electrolyte, a new battery is approximately 75-80% charged.
Do you add water to a battery before or after charging?
Water should always be added after fully charging the battery. Prior to charging, there should be enough water to cover the plates. If the battery has been discharged (partially or fully), the water level should also be above the plates.
How do you activate a dry battery?
Remove vent caps, fill each cell above the top of the splash guard (protection mat covering separators) with approved 1.265 specific gravity battery grade electrolyte. Keep sparks and flames away from battery at all times. Allow electrolyte to saturate plates and separators for 30 minutes.
How do I know when my 12v battery is fully charged?
To check the voltage you’ll need a voltmeter, which can be purchased cheaply from most major automotive parts stores. Check the voltage of your battery using the voltmeter to help determine your next course of action. 12.6V volts or above – Your battery is healthy and fully charged.
When disconnecting the battery the correct tools to use are?
Most but not all battery-cable clamps have 10-millimeter bolts, so you’ll likely need a 10-millimeter open-end wrench to disconnect the cables. A socket-wrench set that includes that same-size socket will be helpful as well. In some cases, you can get by with just an adjustable open-end wrench.
How do you activate a motorcycle?
Make sure the motorcycle gear shifter is in neutral. Squeeze the motorcycle clutch lever with your left hand all the way to the grip. Press the start button with your right thumb. Let the starter motor turn over until the engine fires before you release the start button.
Do I need to charge a new motorcycle battery?
Most motorcycle batteries are lead-acid batteries and should be charged in addition to the charge it receives from your riding. The fact of the matter is unless you are going for a road trip or will be riding continuously for hours, the alternator is not powerful enough to fully charge the battery.
When connecting a motorcycle battery which terminal do you connect first?
When installing your new battery, simply slide the new battery into place and attach the cables to the terminals. This time, attach the positive side first and the negative side second. Secure everything in place using the security belt and replace the motorcycle seat.
How long does it take to charge a Yuasa Battery?
A minimum of 24 hours is normal. It might be impossible to charge an over discharged battery.
How do you check a battery is fully charged?
You need a fairly accurate multimeter to check whether a battery is fully charged. First charge the battery, and when you think it is fully charged, then take it out. Through a multimeter measure the emf between the poles of the battery. The reading should be slightly higher than the battery voltage specification.
How long should a Yuasa Battery Last?
AGM: Sealed AGM batteries typically last 3 to 5 years on average. Typically sealed AGM batteries will give warning before completely dying. They will start slower, and require more charging.
How do you check a Yuasa Battery?
YUASA MIDTRONICS MDX617 (P)
- Select ‘Yuasa Warranty Test’*
- Select application, then battery type.
- Select battery standard ‘SAE’*
- Enter CCA rating of battery (shown on label of battery) For Marine and Leisure batteries use 4 x 20hr capacity e.g. 100Ah Marine battery test @ 400A.
- Press enter to test.
Can you charge an AGM battery with a regular charger?
You can use your regular battery charger on AGM or gel cell batteries. False. These batteries like to be charged slow and low. Many AGM/gel cell battery chargers have microprocessors that collect information from the battery and adjust the current and voltage accordingly.
How do I charge my AGM battery?
The best way to charge an AGM battery is with a charger designed for that specific purpose. When charging, remember that AGM batteries must not be charged over 14.8 volts in most cases. The manufacturer of your particular battery probably has a specification and guide sheet to set some specific rules and guidelines.
How much distilled water do I put in my battery?
While a battery should only be filled after it is completely charged, you should also check the water level before charging to make sure there is just enough water to cover any exposed plates. After charging, add enough water to bring the level to the bottom of the vent, about ¾ below the top of the cell.
How do you know when your car battery needs water?
Check to see if your battery has a green light on top. This usually tells you if the water level is good. If it’s gone dark then your battery needs water, or if it turned yellow then your battery needs some assistance. You should not mess with your car battery on your own!
How do I make distilled water for my battery?
The process of distilling is simple. Heat tap water to the point that it turns to vapor. When the vapor condenses back to water, it leaves behind any mineral residue. The resulting condensed liquid is distilled water.
What happens when a battery is low on water?
Underwatering is when you fail to refill the battery when it reaches a low electrolyte level. Each time you charge your battery, the battery cell will experience a further water loss. If the water level reaches as low as to expose the lead plates to oxygen and hydrogen gas in the battery, it can lead to sulfation.
Why do you put distilled water in batteries?
The electrolyte in a flooded deep cycle battery is a solution of acid and water. Using distilled or deionized water is recommend because it is free from additional minerals you would find in water such as regular tap water. Adding chemicals and minerals can significantly decrease the life of batteries.
Contents