?Rinnai Control-r 2.0 on the App Store.
How do I set up my Rinnai remote?
When setup is complete, the owner will have access to remotely monitor and control their Rinnai tankless water heater using their smart device. 1. Open the Rinnai app. If you are the owner of the module, tap Consumer Sign up.
What is control r app?
The proprietary app and module allow you to have control of your hot water like never before. Our smart home integration allows you to control temperature and turn on recirculation (if applicable) for faster hot water with just a word to your Amazon Alexa, Google Home, or Samsung SmartThings device.
How does Rinnai Control R work?
The Control-R Module attaches easily to the Rinnai Tankless Water Heater by a two-wire interface quickly connecting through your Wi-Fi network for monitoring. Once connected and the free Rinnai mobile app is downloaded, the Rinnai Tankless Water Heater can be controlled using your smart phone or tablet.
How do Rinnai controllers work?
How does a temperature controller work? A temperature controller will take an input signal from a temperature sensor and will in turn create an output signal that is connected to the heating element. The controller will compare actual temperature of a fluid or space to the desired control temperature, or setpoint.
The Push Button mounts near the point of use (such as a kitchen faucet or bathroom sink) and activates the recirculation system. The recirculation system will deactivate after five minutes from initiation or when the water has reached the set temperature.
When you press the “Priority button,” the green light will glow, indicating that the controller controls the temperature and that a water heater is ready. Rinnai water heaters work in the temperature range from 98 F to 140 F, while they come with the factory setting of approximately 120-125 F.
How do I reset my Rinnai WIFI?
Press and hold the Connect button on the module until the LED blinks RED and WHITE, and then release then QUICKLY tap 3 times. This will restore the module back to original factory settings.
How do I reset my Rinnai hot water heater?
Turn off all hot water faucets/taps. Press On/Off button twice. Turn hot water back on and test. You may have to try this a couple times to reset the system.
How do you use control Y?
Alternatively referred to as Control+Y and C-y, Ctrl+Y is a keyboard shortcut most often used to redo an action reversed using the undo command. For example, if you used the Ctrl+Z shortcut to undo what you thought was a mistake, but realize it wasn’t, you could press Ctrl+Y to redo the previous action.
How do you reset the control R module?
Factory Reset Instructions
- FIRST – Press and hold connect for 30 seconds until flashing white, then let go. wait 1 minute until solid red.
- Note: If, after pressing and holding the connect button for 30 seconds, your module is flashing red/white, quickly press the connect button 3x rapidly in a row.
Why is my Rinnai water heater not working?
How to Fix: Check for low flow in the water circulation system which causes short cycling. Confirm there are no obstructions in the combustion chamber or exhaust piping. Confirm no blockage in heat exchanger fins. Clean out heat exchanger fins or replace heat exchanger.
Where is the serial number on a Rinnai?
Our Rinnai Infinity product information & serial number is normally found on the bottom left side of the units.
Does Rinnai have pilot light?
The Rinnai unit won’t operate in the event of a power failure. Rinnai Tankless Water Heaters don’t have a standing pilot light. They use an electronic ignition.
What is Rinnai Sensei?
Rinnai Sensei Tankless Water Heater Product Review
They have a longer lifespan than traditional tank water heaters, and are very energy efficient. Recently, Rinnai has released its line of Rinnai Sensei tankless water heaters. This new product is designed to have the most flexible venting in the industry.
How hot should I set my tankless water heater?
You’ll want to shoot for 100-115 degrees Fahrenheit for your water to be heated. If your groundwater temperature is 60 degrees and you want your shower at 110 degrees, that’s going to be a 50-degree rise.
What is code 12 on Rinnai?
If you’re getting Rinnai error code 12 on your hot water unit, it indicates that a flame failure has occurred on the system. In this instance, your hot water unit has not recognised that there is a flame in the burner box.Incorrect gas pressure supply your hot water unit.
Why is my tankless hot water heater beeping?
Your tankless water heater will beep and display an error code to alert you to a problem with the system. Tankless water heaters will alert you with an audible alarm when service is required, a component fails, or a gas or water leak is present.
How do you unlock Rinnai tankless?
All of the controllers in the system are also locked. To unlock the controller press the Priority button and the up button together for 5 seconds.
Why am I not getting hot water from my tankless water heater?
Because tankless units only heat water as it’s needed, running too many hot water appliances at the same time could mean the unit just can’t keep up.On the other hand, your no hot water problem could be cause by a bigger issue such as: Plugged heat exchanger (due to hard water) A blocked vent/air intake.
What to check when there’s no hot water?
If there is no hot water, it probably means that the tank is leaking. An empty tank is a serious problem and is not at all energy efficient. Inspect the connections between the appliance and its valves as well as the pipes. If those are secure, check the tank’s compartment.
Contents