Terminal posts include corner posts and gate posts. They are usually taller and larger than line posts. Line posts are the vertical support structures for the chainwire fence which are usually spaced 10 or less feet apart. Other horizontal logs could rest on these line posts.
Can you use terminal post as line post?
Set the terminal posts in concrete using a concrete mix. You can use 1 part cement, 2 parts sand, and 4 parts gravel.Line posts should not be spaced more than 10 feet apart. For example, if the length between two terminal posts is 30 feet, then line posts would be spaced 10 feet apart (see chart below).
What is a line post used for?
The Line Post
These fences were typically made of felled trees and were usually used to keep livestock in one place. A hole was typically dug into the ground, and the end of a wood post was placed inside before the hole was filled to support the post.
What is the difference between a line post and a corner post?
Corner post – A post at the corner where two lines of fencing meet, usually at a 90-degree angle.End post – A post that marks the end of a fence line, with holes on only one side for attaching rails. End posts are typically used as gate posts or terminal posts, such as where the fence abuts a house.
What is a terminal post in a chain link fence?
Drive stakes into the ground along the extension of your property line and stretch a string between each stake as illustrated in figure A. Set corner, end and gate post (also known as terminal posts) positions 4″ inside line so concrete footings do not encroach onto any adjoining property.
How deep should terminal post?
Dig the terminal post holes (about 8 inches in diameter and 30 inches deep). Slope the sides with wider at the bottom than at the top. Mark the ground line on the posts with chalk. The height of terminal post above level ground should equal to the height of the fabric plus 2 inches.
Do line posts need concrete?
You can install a chain link fence without using concrete, but it is not recommended. Anchoring each fence post in concrete is the best way to ensure your fence will stand straight and tall for many years.
Why would you not make a fence with a string?
The downside to a string is that it is 100% in the way about 100% of the time. It’s what strings do. It’s not their fault. To hold it out of the way to dig a hole for example, I pull it to the side, sink my scratch awl into the ground and then hook the string on it.
What is the strongest wood for fence?
Redwood
Redwood is arguably the most extensively used type of wood for wood fencing and even though it comes at a high cost, redwood’s quality, durability, and aesthetic value make it among the best options.
What’s the best wood for fence posts?
Redwood is one of the most widely used wood types for wooden fencing. It is expensive, but it more than compensates for its price with durability, quality, and beauty. It is naturally resistant to rot and insects. It is therefore considered the best wood for fencing.
What size fence post do I need for a 5ft fence?
4in x 4in
Use 4in x 4in posts for fences of 5ft and over and 3in x 3in posts for anything under 5ft.
How far apart should line posts be for chain link fence?
SPACING FENCE POSTS
As chain link fence posts are smaller and sturdier than many other types, the holes should be smaller and can be farther apart. Follow the fence manufacturer’s instructions for spacing, which typically ranges from 4-10′ apart—spacing should not exceed 10′ on-center. (fig.
What kind of metal is a chain link fence post?
A chain-link fence (also referred to as wire netting, wire-mesh fence, chain-wire fence, cyclone fence, hurricane fence, or diamond-mesh fence) is a type of woven fence usually made from galvanized or LLDPE-coated steel wire.
How far apart do you put the poles for a chain link fence?
Chain link fence posts are typically spaced a maximum of ten feet apart. For aesthetic reasons, space posts evenly, but do NOT exceed ten feet between posts. If you plan on installing privacy slats or another type of material that will increase wind load, consider using 8′ or 6′ post spacing.
How far apart should gate posts be?
Single walk gates require 3¾” for hinges and latches and double drive gates require 5½”. For example, a 3 foot walk gate should measure 32¼” wide. Adding 3¾” to the width means that the distance between posts (inside face to inside face) should be 36″.
How much does a 100 foot chain link fence cost?
Average Chain-Link Cost Per Foot
| Linear Feet | 4-foot Tall | 6-foot Tall |
|---|---|---|
| 50 | $600 | $750 |
| 100 | $1,200 | $1,500 |
| 150 | $1,800 | $2,250 |
| 200 | $2,400 | $3,000 |
How deep should a 7 foot fence post be?
The general rule of thumb when setting a post is that the depth of the post’s hole needs to be one-third to one-half of the actual above-ground height of the post.
Can you reuse fence posts with concrete?
Things You’ll Need
Posts with concrete at the base are the most difficult to remove and reuse because the concrete base is larger than the post, which makes pulling it up through the ground much harder.
Is 2 feet deep enough for fence posts?
Dig post hole so diameter of the hole is 3 times the width of the post (i.e., the hole for a 4” wood post should be about 12 inches wide). The depth of the hole should be 1/3-1/2 the post height above ground (i.e., a 6-foot tall fence would require a hole depth of at least 2 feet).
Can you install fence posts without concrete?
Did you know that it is actually completely possible to set wooden posts in your yard without using ANY concrete? It’s true! Setting them without concrete will save you time and money, but there is a correct way to do it in order to prevent rot.
Can you put dry concrete in a post hole?
Fast-setting concrete is ideal for setting posts because there’s no mixing—you simply pour the dry concrete from the bag right into the hole, then add water.
Contents