Hackney suggests a minimum of 7 feet but says 7-4 and 7-6 rods are best. The longer rod picks up line quicker and helps you power fish away from cover. For casting jigs into deeper water, he likes a 7-6 with a lighter tip. Again, the longer rod improves hook sets on fish farther away and in deeper water.
What gear ratio is best for jig fishing?
A slow reel is the ideal choice for most crankbaiting. A reel with about a 5:1 gear ratio is going to help you get your baits to their maximum depth and also give you superior feel, so you know exactly what’s going on with your lure. My favorite cranking reel is the new Lew’s BB1.
What rod do I need for jig fishing?
The ideal rod for fishing finesse jigs is a 7 foot medium power, fast action casting rod.
How do I choose the right gear ratio?
The conventional procedure for selecting gear ratios is to pick ratios that run the engine rpm to redline at the end of the medium and longest straights, and pick the lower gear ratios to minimize the rev drop at each shift. This method minimizes the number of shifts per lap.
What is a 8.1 gear ratio good for?
High gear ratio reels | 7.1:1 thru 8.1:1
High gear ratios are best for techniques where taking up slack and bringing a bait back to the boat are critical. Topwaters, jerkbaits, jigs, plastics and even lipless crankbaits warrant the use of a high-speed reel.
When should you throw a jig?
Jigs shine best when imitating craws. Throw a jig around shallow wood cover, near docks, or anywhere else bass would be feasting on craws. Jigs, in my opinion, are also more suited for trophy hunting. The bigger, bulkier presentation is more likely to draw strikes from your new PB than a slimmer Texas Rig.
What is the best gear for acceleration?
So here’s the answer – the point to change up a gear for maximum acceleration is the point when you’ll get better acceleration in the higher gear. In other words, the point when you’ll generate more torque at the wheels in the higher gear.
What are 3.55 gears good for?
With a 3.55 being a higher numerical number, Garrison says it will put more torque to the tire, allowing for faster acceleration and better performance on hill climbs. However, the tradeoff is burning more fuel through a higher engine speed.
What are 3.73 gears good for?
Is 3.73 a good gear ratio? FACT: A 3.73 axle ratio is ideal for towing heavy loads on flat terrain and will produce increased fuel economy during steady-state, long-distance highway driving.
What is a 7.5 1 gear ratio good for?
7.5:1 Reel – With my 7.5:1 gear-ratio reel, I like to use this reel when I’m fishing single-hook lures like a buzzbait, a spinner bait, bladed jigs and a frog.
Are more ball bearings in a reel better?
When they’re considering purchasing a reel, anglers can’t help but notice how many bearings it offers. But the truth is that reels with lots of bearings aren’t necessarily better. The quality of the bearings, and the quality of the reel that contains them, are much more important than the number of bearings.
What is the difference in baitcasting gear ratios?
So, the higher the gear ratio, the faster the retrieve speed of your reel. In general, casting reels are faster than spinning reels, which usually go from 5.1:1 to around 6.5:1, while baitcasters start around 5.5:1, and go all the way up to 9.3:1.
What color jig is best for bass?
Black and blue offers the ultimate in contrast, which gives bass a target any time the water’s got some stain. Use a black and blue jig in dirty water, during low light conditions, and anytime around vegetation.
Do you need a trailer on a jig?
Fishing a jig without a jig trailer is like eating a salad without dressing or toast without jelly. None have the same pizzazz without the additional condiment. Although a bass would probably bite a standalone jig, the allure of a jig trailer causes bass anglers to consider it standard equipment for jig fishing.
Do I need a sinker with a jig head?
You’ll need a sinker or a weighted jighead to get a buoyant lure like a plastic worm or tube bait to the bottom and keep it there.
What size jig head should I use?
The best jig head size is usually still the 1/8 ounce or 1/4 ounce because they are usually in the upper parts of the water column.
At what Rev Should you change gear?
Changing up gears
Under normal driving conditions, this means changing up if the rev counter reaches between 2500-3000rpm. Under hard acceleration, you will change up a gear when you feel the acceleration drop away, which is usually above 6000rpm in a petrol-powered engine, but less if it’s diesel-powered.
At what rpm should you downshift?
Shift thoroughly so your shift can be smoother when you shift down. Make sure you only downshift if your rpm’s are 5,500 or below that way you can get in the power band range.
What rpm should you shift gears?
2,500-3,000 RPM
Generally, you want to shift gears when your car reaches 2,500-3,000 RPM. Eventually, you will know when to shift by sound and feel.
Is 3.31 or 3.55 axle ratio better?
Normally, the 3.31 would get you better gas mileage, on highway. But, with the 3.55 you will get a bit more pulling power so less time at higher RPM to get your trailer moving and when going uphill. If most of your towing is flat highway, the 3.31 should do you fine.
Is 3.55 or 3.73 better?
3.55 gears will give you better gas mileage while 3.73 gears give you better acceleration and performance. The numbers you are using are common Final Drive Axle Ratios for vehicles, so the question will be answered in that context.
Contents